1、Designation:D406014Standard Test Method forAbrasion Resistance of Organic Coatings by the TaberAbraser1This standard is issued under the fixed designation D4060;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination of the
3、resis-tance of organic coatings to abrasion produced by the TaberAbraser on coatings applied to a plane,rigid surface,such as ametal panel.1.2 The values stated in SI units are to be regarded as thestandard,with the exception of mils when determining coatingthickness.1.3 This standard is similar in
4、content(but not technicallyequivalent)to ISO 77842.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of reg
5、ulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D823 Practices for Producing Films of Uniform Thicknessof Paint,Varnish,and Related Products on Test PanelsD968 Test Methods for Abrasion Resistance of OrganicCoatings by Falling AbrasiveD1005 Test Method for Measurement of D
6、ry-Film Thick-ness of Organic Coatings Using MicrometersD2240 Test Method for Rubber PropertyDurometer Hard-nessD3924 Specification for Standard Environment for Condi-tioning and Testing Paint,Varnish,Lacquer,and RelatedMaterialsD7091 Practice for Nondestructive Measurement of DryFilm Thickness of N
7、onmagnetic Coatings Applied toFerrous Metals and Nonmagnetic,Nonconductive Coat-ings Applied to Non-Ferrous MetalsG195 Guide for Conducting Wear Tests Using a RotaryPlatform Abraser2.2 Other Standards:ISO 77842 Paints and varnishesDetermination of resis-tance to abrasionPart 2:Rotating abrasive rubb
8、er wheelmethod33.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Abrasion resistance can be expressed as one or moreof the following terms:3.1.2 wear index,n1000 times the loss in weight inmilligrams per cycle.3.1.3 weight loss,nthe loss in weight in milligrams,determined at a sp
9、ecified number of cycles.3.1.4 wear cycles per mil,nthe number of cycles ofabrasion required to wear a film through to the substrate per mil(0.001 in.)of film thickness.4.Summary of Test Method4.1 The organic coating is applied at uniform thickness to aplane,rigid panel and,after curing,the surface
10、is abraded usingrotary rubbing action under controlled conditions of pressureand abrasive action.The test specimen,mounted on a turntableplatform,turns on a vertical axis,against the sliding rotation oftwo abrading wheels.One abrading wheel rubs the specimenoutward toward the periphery and the other
11、,inward toward thecenter.The resulting abrasion marks form a pattern of crossedarcs over an area of approximately 30 cm2.4.2 Abrasion resistance is calculated as loss in weight at aspecified number of abrasion cycles,as loss in weight percycle,or as number of cycles required to remove a unit amounto
12、f coating thickness.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.23 on Physical Properties of Applied Paint Films.Current edition approved Dec.1,2014.Published January 201
13、5.Originallyapproved in 1981.Last previous edition approved in 2010 as D4060 10.DOI:10.1520/D406014.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Documen
14、t Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken
15、,PA 19428-2959.United States1 5.Significance and Use5.1 Coating on substrates can be damaged by abrasionduring manufacturing and service.This test method has beenuseful in evaluating the abrasion resistance of coatings.Ratingsproduced by this test method have correlated well with ratingsproduced by
16、the falling abrasive values in Test Method D968.5.2 For some materials,abrasion tests utilizing the TaberAbraser may be subject to variation due to changes in theabrasive characteristics of the wheel during testing.Dependingon abradant type and test specimen,the wheel surface maychange(that is,become clogged)due to the adhesion of debrisgenerated during the test and must be resurfaced at morefrequent intervals as agreed upon by the interested parties.Todetermine if more frequent resurfacing is r
