1、A N A M E R I C A N N A T I O N A L S T A N D A R D Metric Series Socket Set Screws ASMEIANSI B18.3.6M-1986,.-._-REAFFIRMED 1993 Government Kev Words:Setscrew,Hexagon,Socket-Metric FOR CURRENT COMMIlTEE PERSONNEL PLEASE SEE ASME MANUAL AS-1 1 SPONSORED AND PUBLISHED BY T H E A M E R I C A N S O C I
2、E T Y OF M E C H A N I C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.1001 7 Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Un
3、controlled when printed.REAFFIRMED 2002FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgDate of Issuance:February 28,1987 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standa
4、rd issued to this Edition.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an oppo
5、rtunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary d
6、evice,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor as
7、sume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s1 or person(s)affiliated with indust
8、ry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual volunteers.No part of th
9、is document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright 0 1987 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyrighted material licensed to Stanford University by
10、 Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORD(This Foreword is not part of ASMElANSl B18.3.6M-1986.1 Americav.National Standards Committee B18 for the standardization of bolts,screws
11、,nuts,rivets,and similar fasteners was organized in March 1922 as Sectional Committee B18 under the aegis of the American Engineering Standards Committee(later the American Standards Association,then the United States of America Standards Institute and,as of October 6,1969,the American National Stan
12、dards Institute)with the Society of Automo-tive Engineers and the American Society of Mechanical Engineers as joint sponsors.Subcommittee No.9 was established in April 1929 to undertake the development and oversee the maintenance of standards covering socket head cap screws and set screws.In line wi
13、th a general realignment of the subcommittee structure on April 1,1966,Subcommit-tee 9 was redesignated Subcommittee 3.Over the intervening years this activity has pro-duced several versions of American National Standards covering inch series socket cap,shoulder,and set screws bearing the B18.3 desi
14、gnation.At the December 4,1974 meeting of American National Standards Committee B18,Sub-committee 3 was assigned the task of preparing standards for metric series socket screw products paralleling that contained in the latest ANSI B 18.3 document.The Subcommittee was also instructed to continue coor
15、dinating that activity with the International Standards Organization,IS0 Technical Committee 2,and Working Group 3,and,to the extent possi-ble,to keep the proposals for metric standards under development in conformance with agreements reached therein.Subsequent meetings of Subcommittee 3,held in Feb
16、ruary 1975 and January 1976,re-sulted in general agreement on the following basic principles to be considered in developing the metric version of the standard.(a)To assure consumers continuity of performance integrity consistent with inch socket screw products,the metric standards should maintain the same q.uality levels as their inch counterparts.(b)To facilitate and expedite the processing,acceptance,and adoption of the metric ver-sions,proposals for the various product categories should be pr