1、ASME B29.24-2002(Revision of ASME B29.24M-1995)ROLLER LOADCHAINS FOROVERHEAD HOISTSA N A M E R I C A N N A T I O N A LS T A N D A R DASME B29.24-2002(Revision of ASME B29.24M-1995)ROLLER LOADCHAINS FOROVERHEAD HOISTSA N A M E R I C A N N A T I O N A LS T A N D A R DREAFFIRMED 2016Intentionally left
2、blank AN AMERICAN NA TIONALST ANDARDROLLER LOAD CHAINS FOROVERHEAD HOISTSASME B29.24-2002(Revision of ASME B29.24M-1995)Date of Issuance:September 26,2002This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of thereq
3、uirements of this Standard issued to this Edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or
4、standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agenci
5、es,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyone
6、utilizing a standardagainst liability for infringementof any applicable letterspatent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsib
7、ility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME
8、 procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Av
9、enue,New York,NY 10016-5990Copyright 2002 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.CONTENTSForeword.ivCommittee Roster.vCorrespondence With the B29 Committee.vi1Scope.12Purpose.13Roller Load Chains.13.11Nomenclature.3.21General Proportions.3.31Numbering Syste
10、m.3.41Minimum Ultimate Tensile Strength.3.51Length Tolerance.3.64Measuring Load.3.74Preload.3.84General Chain Dimensions.4Roller Chain Inspection,Replacement,and Maintenance.44.14Chain Inspection.4.27Maintenance.4.38Replacement of Load Chain.Figures1Typical Hoist Roller Load Chain.22Overhead Hoist.4
11、3Elongation Measurement.54Illustration of Camber and Twist.55Hook.66Pin Turning.67Inspection of Chain Rollers.78Inspection for Tight Joints.7Table1General Load Chain Dimensions.3iiiFOREWORDA number of specialized roller chains are made and supplied to original equipmentmanufacturers for use as load
12、chains on overhead hoists.Although these chains are ofsimilar design and construction,and are usually dimensionally interchangeable with equivalentpitch ANSI B29.1,Power Transmission Roller Chains,they differ in that they are normallymade using select steels and/or specially treated chain parts to p
13、rovide for the higher tensileand fatigue strength properties required to meet the rate load capacitites of the overheadhoists in which they are used.Hoist load chains are consequently assigned special chain numbers to distinguish themfrom equivalent pitch B29.1 or other roller chains,which even if d
14、imensionaly interchangeable,may not have the necessary strength or special characteristics for replacement of the originalhoist load chain.It was recognized by the Roller Chain Technical Committee of the American ChainAssociation that a potential risk of personal injury could occur as a result of ch
15、ain failureif the original load chiain was inadvertently replaced by a lower strenght chain,or if properuse,care,and maintenace procedures were not followed.Consequently,a committee wasformed in October 1978 to prepare a standared for chains used in overhead hoists to serveas a guide to users and pu
16、rchasers of overhead hoists with regard to hoist chain designations,dimensions,ultimate strength,maintenance,and inspection procedures,and restrictions forchain replacement.The standard would also provide a reference in related standards suchas ASME/ANSI B30.16,Overhead Hoists(Underhung),(latest edition)with regard to chaincare and replacement.In tabulating dimensional information in this Standard,customary inch-pound units havebeen used.Additionally,companion tabulations have been included in o