1、AN AMERICAN NATIONAL STANDARDASME B5.60a-2005ADDENDAtoASME B5.60-2002WORKHOLDING CHUCKS:JAW TYPE CHUCKSIncorporating ASME B5.60.1,ASME B5.60.4,and ASME B5.60.5THE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park Avenue O New York,NY 10016Copyright 2009 by the American Society of Mechanical Enginee
2、rs.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of I
3、ssuance:December 15,2005ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to as
4、sure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large
5、.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyoneutilizing a standardagains
6、t liability for infringementof any applicable letterspatent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by fed
7、eral agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies,w
8、hich precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-599
9、0Copyright 2005 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thoms
10、on Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME B5.60a-2005Following approval by the ASME B5 Committee and ASME,and after public review,ASME B5.60a-2005was approved by the American National Stan
11、dards Institute on February 24,2005.Addenda to the 2002 edition of ASME B5.60 are issued in the form of replacement pages.Revisions,additions,and deletions are incorporated directly into the affected pages.It is advisable,however,that thispage,the Addenda title and copyright pages,and all replaced p
12、ages be retained for reference.SUMMARY OF CHANGESThis is the first Addenda to be published to ASME B5.60-2002.Replace or insert the pages.Changes given below are identified on the pages by a margin note,(a),placednext to the affected area.The pages not listed are the reverse sides of the listed page
13、s and contain nochanges.PageLocationChangeiiiContentsUpdated to reflect AddendaivForewordUpdated to reflect AddendavCommittee RosterUpdated to reflect AddendaviiPrefaceUpdated to reflect Addenda1121ASME B5.60.5Added(c)Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may
14、 be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Copyright 2009 by the American
15、Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncont
16、rolled when printed.INTENTIONALLY LEFT BLANK CONTENTS(a)Foreword.ivStandards Committee Roster.vCorrespondence With the B5 Committee.viPreface.viiASME B5.60.1General Description and Definitions of Terms.1ASME B5.60.2Chuck-to-Spindle Interface(to be added).ASME B5.60.3Jaw Mountings(to be added).ASME B5.60.4Performance Testing.5ASME B5.60.5Safety Code of Practice.11ASME B5.60.6Chuck Assembly:Sizes and Designation(to be added).iiiCopyright 2009 by the American Society of Mechanical Engineers.No repr