1、9009275 0024486 T 5 T =E R RATA ANSI B94.4-1976 PRECISION INDEXABLE INSERT CARTRIDGES Page 1 O,Table 2.L,max.column,Size 1,should read,8 mm(0.3 15).Page 14,Table 5.Column D,Cart.Size 25,should read,36 mm(1.417).THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS 345 East 47th Street,New York,N.Y.10017 Copy
2、right ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-9007275 0024487 77b A M E R I C A N N A T I O N A L S T A N D A R
3、D Precision I ndexable Insert Cartridges ANSI B94.48-1976 SECRETARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y OF M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 001 7 345 East 47th Street:%&1 I,.Copyright ASME Inter
4、national Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-No part of this document may be reproduced in any form,in an electronic retrieval
5、system or otherwise,without the prior written permission of the publisher.Copyright 1977 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyr
6、tyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024489 769 F O R E W O R D The material contained in this Standard was developed by Technical Committee 1,Carbide and Oxide Tools of American National Standards Committee B94,Cutt
7、ing Tools,Holders,Drivers,and Bushings,in conjunction with I.S.O./TC29/WG9 Committee,after a thorough investigation of all factors involved.It is based on sound Engineering practice and reflects the requirements of the industry.The Standard was submitted to American National Standards Committee B94,
8、Cutting Tools,Holders,Drivers,and Bushings and was approved by letter ballot.The Secretariat,The American Society of Mechanical Engineers approved the Standard.The Standard was approved by American National Standards Institute on July 23,1976 and designated ANSI B94.48-1976.111 Copyright ASME Intern
9、ational Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024490 480 9 AMERICAN NATIONAL STANDARDS COMMITTEE B94 CUTTING TOOLS,HOLDE
10、RS,DRIVERS AND BUSHINGS(The following is the roster of the committee at the time of the approval of the Standard)OFFICERS Harry McLinden,Chairman A.M.Mezey,Vice-chairman Kurt Wessely,Secretary STANDARDS COMMITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Lat
11、ham,New York G.L.Scott,alternate,American Gear Manufacturers Associations,Washington,D.C.AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE M.E.Merchant,Dr.,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C.J.Oxford,Jr.,National Twist Drill&Tool Company,Roc
12、hester,Michigan G.F.Wilson,alternate,DoAll Company,Des Plaines;Illinois W.E.Montgomery,Firth Sterling,Inc.,McKeesport,Pennsylvania A.P.Wherry,alternate,Cemented Carbide Producers Association CEMENTED CARBIDE PRODUCERS ASSOCIATION GENERAL SERVICES ADMINISTRATION W.R.Wacker,General Services Administra
13、tion,Washington,D.C.Richard Schrade,Clemson Brothers,Inc.,Middletown,N.Y.C.M.Stockinger,aiternate,Hack&Band Saw Manufacturers Association,Cleveland,Ohio HACK&BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA METAL CUTTING TOOL INSTITUTE W.A.Wagner,Cleveland Twist Drill Company,Cleveland,Ohio R.M.Byrne,a
14、lternate,Metal Cutting Tool Institute,New York,N.Y.NATIONAL ASSOCIATION OF PUNCH MANUFACURERS R.E Smith,Dayton Progress Corp.,Dayton,Ohio NATIONAL BUREAU OF STANDARDS J.R.Pidgeon,National Bureau of Standards,Washington,D.C.NATIONAL MACHINE TOOL BUILDERS ASSOCIATION G.F.Wilson,DoAll Company,Des Plain
15、es,Illinois E.J.Loeffler,alternate,National Machine Tool Builders Association,McLean,Virginia SOCIETY OF AUTOMOTIVE ENGINEERS To be appointed SOCIETY OF CARBIDE ENGINEERS C.H.Lang,Society of Carbide Engineers,Bridgeville,Pennsylvania K.A.Lundell,The Producto Machine Co.,Jamestown,N.Y.H.J.Moffatt,Bar
16、tonville,Iliinois W.N.Moore,The Ford Motor Co.,Dearborn,Michigan SOCIETY OF MANUFACTURING ENGINEERS TELEPHONE GROUP,THE i.L.Parrish,Western Electxic Co.,Inc.,Chicago,Illinois S.P.Rogacki,altemate,Western Electric Co.,Inc.,Kearny,N.J.U.S.DEPARTMENT OF THE AIR FORCE To be appointed V.,Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:25 MSTNo reproduction or networking permitted without