1、AN AMERICAN NATIO NAL STANDARDASME Y14.44-2008Reference Designations for Electrical and Electronics Parts and EquipmentEngineering Drawing and Related Documentation PracticesCopyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written co
2、nsent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.44ADOPTION NOTICEASME Y14.44,Reference Designations for Electrical
3、 and Electronics Parts and Equipment,was adopted on22 July 2008 for use by the Department of Defense(DoD).Proposed changes by DoD activities must be submittedto the DoD Adopting Activity:Commander,U.S.Army Research,Development and Engineering Center(ARDEC),ATTN:AMSRD-AAR-QES-E,Picatinny Arsenal,NJ 0
4、7806-5000.Copies of this document may be purchased fromThe American Society of Mechanical Engineers(ASME),22 Law Drive,P.O.Box 2900,Fairfield,NJ 07007-2900,http:/www.asme.org.Custodians:Adopting Activity:Army ARArmy ARNavy SAAir Force 16(ProjectDRPR-2008-003)Review Activities:Army CR,IE,MI,PT,TM2Nav
5、y AS,CG,CH,EC,MC,NP,TDAir Force 13,99DLA DHOSD SENSA NSOther CM,MP,DC2NOTE:The activities listed above were interested in this document as of the dateof this document.Since organizations and responsibilities can change,you shouldverify the currency of the information above using the ASSIST Online da
6、tabaseat http:/assist.daps.dla.mil.AMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material license
7、d to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.44-2008Reference Designationsfor Electrical andElectronics Partsand EquipmentEngineering Drawing and RelatedD
8、ocumentation PracticesAN AMERICAN NATIONAL STANDARDCopyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by St
9、anford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:November 21,2008The next edition of this Standard is scheduled for publication in 2013.There will be no addenda orwritten interpretations of the requirements of this Standard issued
10、 to this edition.Periodically certain actions of the ASME Y14 Committee may be published as Cases.Cases arepublished on the ASME Web site under the Committee Pages at http:/cstools.asme.org as they areissued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code o
11、r standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed cod
12、e or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any po
13、sition with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or s
14、tandard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or ind
15、ustry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in an
16、y form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2008 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scient