ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:93.95KB ,
资源ID:168159      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/168159.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_B_636_-_B_636M_-_15.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_B_636_-_B_636M_-_15.pdf

1、Designation:B636/B636M15Standard Test Method forMeasurement of Internal Stress of Plated Metallic Coatingswith the Spiral Contractometer1This standard is issued under the fixed designation B636/B636M;the number immediately following the designation indicates the yearof original adoption or,in the ca

2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the use of the spiral contracto-meter for measuring the internal stress

3、 of metallic coatings asproduced from plating solutions on a helical cathode.The testmethod can be used with electrolytic and autocatalytic depos-its.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact

4、 equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of

5、 this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:E177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaborato

6、ry Study toDetermine the Precision of a Test Method3.Terminology3.1 Definitions:3.1.1 compressive stress()stress that tends to cause adeposit to expand.3.1.2 internal stressthe net stress that remains in a depositwhen it is free from external forces.The internal stress tends tocompress or stretch th

7、e deposits.3.1.3 tensile stress(+)stress that tends to cause a depositto contract.4.Summary of Test Method4.1 The test method of measuring stress with the spiralcontractometer is based on plating on the outside of a helix.The helix is formed by winding a strip around a cylinder,followed by annealing

8、.In operation,one end of the helix isfixed and the other is allowed to move as stresses develop.Thefree end is attached to an indicating needle through gears thatmagnify the movement of the helix.As the helix is plated,thestress in the deposit causes the helix to wind more tightly or tounwind,depend

9、ing on whether the stress is compressive()ortensile(+).From the amount of needle deflection and otherdata,the internal stress is calculated.4.2 With instrument modifications,the movement of thehelix can be measured electronically instead of mechanically asdescribed in 4.1.5.Significance and Use5.1 T

10、he spiral contractometer,properly used,will givereproducible results(see 9.5)over a wide range of stressvalues.Internal stress limits with this method can be specifiedfor use by both the purchaser and the producer of plated orelectroformed parts.5.2 Plating with large tensile stresses will reduce th

11、e fatiguestrength of a product made from high-strength steel.Maximumstress limits can be specified to minimize this.Other propertiesaffected by stress include corrosion resistance,dimensionalstability,cracking,and peeling.5.3 In control of electroforming solutions,the effects ofstress are more widel

12、y recognized,and the control of stress isusually necessary to obtain a usable electroform.Internal stresslimits can be determined and specified for production control.5.4 Internal stress values obtained by the spiral contracto-meter do not necessarily reflect the internal stress values foundon a par

13、t plated in the same solution.Internal stress varies withmany factors,such as coating thickness,preparation ofsubstrate,current density,and temperature,as well as thesolution composition.Closer correlation is achieved when thetest conditions match those used to coat the part.1This test method is und

14、er the jurisdiction ofASTM Committee B08 on Metallicand Inorganic Coatings and is the direct responsibility of Subcommittee B08.10 onTest Methods.Current edition approved Nov.1,2015.Published December 2015.Originallyapproved in 1978.Last previous edition approved in 2010 as B636 84(2010).DOI:10.1520

15、/B0636_B0636M-15.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Apparatus6.1 The spiral contractometer is described by A.Brennerand S.Senderoff.2NOTE1Spiral contractometers are available from many of thesuppliers of nickel sulfamate.6.

16、2 Helices shall be stopped-off on the inside to preventplating.Helices are available with or without a permanent inertcoating on the insides(see Appendix X1).6.3 The clamps holding the helix to the contractometer shallbe coated with an inert nonconductive coating to prevent theirplating and acting as thieves.6.4 For testing electroplating solutions,anodes are placedequidistant from the helix and symmetrically positioned toproduce even plate distribution.A minimum of four anodes isrequired.A conc

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2