1、Designation:D9315aDesignation:34/99Standard Test Methods forFlash Point by Pensky-Martens Closed Cup Tester1This standard is issued under the fixed designation D93;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revi
2、sion.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.INTRODUCTIONThis flash point test method is a dynamic test m
3、ethod which depends on specified rates of heatingto be able to meet the precision of the test method.The rate of heating may not in all cases give theprecision quoted in the test method because of the low thermal conductivity of some materials.Thereare flash point test methods with slower heating ra
4、tes available,such as Test Method D3941(forpaints,resins,and related products,and high viscosity products in the range of 0 C to 110 C),wherethe test conditions are closer to equilibrium.Flash point values are a function of the apparatus design,the condition of the apparatus used,andthe operational
5、procedure carried out.Flash point can therefore only be defined in terms of a standardtest method,and no general valid correlation can be guaranteed between results obtained by differenttest methods,or with test apparatus different from that specified.1.Scope*1.1 These test methods cover the determi
6、nation of the flashpoint of petroleum products in the temperature range from40 C to 370 C by a manual Pensky-Martens closed-cupapparatus or an automated Pensky-Martens closed-cupapparatus,and the determination of the flash point of biodieselin the temperature range of 60 C to 190 C by an automatedPe
7、nsky-Martens closed cup apparatus.NOTE1Flash point determinations above 250 C can be performed,however,the precision has not been determined above this temperature.For residual fuels,precision has not been determined for flash pointsabove 100 C.The precision of in-use lubricating oils has not beende
8、termined.Some specifications state a D93 minimum flash point below40 C,however,the precision has not been determined below thistemperature.1.2 Procedure A is applicable to distillate fuels(diesel,biodiesel blends,kerosine,heating oil,turbine fuels),new andin-use lubricating oils,and other homogeneou
9、s petroleumliquids not included in the scope of Procedure B or ProcedureC.1.3 Procedure B is applicable to residual fuel oils,cutbackresidua,used lubricating oils,mixtures of petroleum liquidswith solids,petroleum liquids that tend to form a surface filmunder test conditions,or are petroleum liquids
10、 of such kine-matic viscosity that they are not uniformly heated under thestirring and heating conditions of Procedure A.1.4 Procedure C is applicable to biodiesel(B100).Since aflash point of residual alcohol in biodiesel is difficult to observeby manual flash point techniques,automated apparatus wi
11、thelectronic flash point detection have been found suitable.1.5 These test methods are applicable for the detection ofcontamination of relatively nonvolatile or nonflammable ma-terials with volatile or flammable materials.1.6 The values stated in SI units are to be regarded as thestandard.The values
12、 given in parentheses are for informationonly.NOTE2It has been common practice in flash point standards for manydecades to alternately use a C-scale or an F-scale thermometer fortemperature measurement.Although the scales are close in increments,they are not equivalent.Because the F-scale thermomete
13、r used in thisprocedure is graduated in 5 F increments,it is not possible to read it tothe 2 C equivalent increment of 3.6 F.Therefore,for the purposes ofapplication of the procedure of the test method for the separate tempera-ture scale thermometers,different increments must be used.In this testmet
14、hod,the following protocol has been adopted:When a temperature isintended to be a converted equivalent,it will appear in parenthesesfollowing the SI unit,for example 370 C(698 F).When a temperatureis intended to be a rationalized unit for the alternate scale,it will appearafter“or,”for example,2 C o
15、r 5 F.1These test methods are under the joint jurisdiction ofASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and are the direct responsibilityof Subcommittee D02.08 on Volatility.In the IP,these test methods are under thejurisdiction of the Standardization Committee.Current editi
16、on approved Oct.15,2015.Published November 2015.Originallyapproved in 1921.Last previous edition approved in 2015 as D93 15.DOI:10.1520/D0093-15A.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-pria