ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:50.31KB ,
资源ID:168202      下载积分:8 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/168202.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_957_-_12.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_957_-_12.pdf

1、Designation:D95712Standard Practice forDetermining Surface Temperature of Molds for Plastics1This standard is issued under the fixed designation D957;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number

2、in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice is intended for determining the tempera-ture at a specified point or points on the surface of the cavityand base of a mold for plas

3、tics.By determining the temperatureat as many points as deemed necessary,the overall temperaturecondition of the surface can be determined.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to

4、address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.2

5、.Summary of Practice2.1 With the use of a calibrated surface or radiation(infra-red)non-contact pyrometer,the overall temperature conditionof a mold for plastics can be determined by taking readings ata specified point or many points on the mold surface.3.Significance and Use3.1 The properties of mo

6、lded parts and the ease of produc-ing satisfactory specimens are influenced by the temperature ofthe mold.It is desirable to know the actual mold temperature,which can differ from the mold temperature control medium.3.2 The user needs to be aware of temperature differencesacross the mold/thermocoupl

7、e interface and at leads,and takeappropriate precautions to minimize such differences.4.Apparatus4.1 Surface PyrometerA calibrated temperature devicedesigned to measure surface temperatures that is traceable tothe international system of units(SI)through a nationalmetrology institute(NMI)2accurate t

8、o within 61.5C shall beused.4.2 Non-Contact PyrometerA Radiation(infrared)Ther-mometer that is traceable to the international system of units(SI)through a national metrology institute(NMI)2accurate towithin 61.5C shall be used.Radiation Thermometers withselectable emissivity shall be set to the esti

9、mated emissivity ofthe surface to be measured.An emissivity correction shall bemade when using Radiation Thermometers with a presetemissivity.5.Procedure5.1 The size,shape,and contours of a mold determine thelocation and number of points at which temperature readingsare observed.Take temperature rea

10、dings at as many points asdeemed necessary to determine the temperature condition ofthe mold surface.At a minimum,it is suggested that tempera-tures be measured at the mold center,near the edge,and at leasttwo different but intermediate points between the center andedge.5.2 Place the thermocouple of

11、 the pyrometer at any speci-fied point on the surface of the cavity and base of the mold,making certain that good contact is maintained between thetwo(see Note 2).Maintain contact until the scale reachesequilibrium.Record the temperature reading on the scale at thispoint.NOTE2Wax,or any suitable mat

12、erial with a low melting temperature,can be used to ensure intimate contact between the mold surface and thethermocouple of the pyrometer.This is accomplished by allowing a smallportion of the material to melt at the point where the temperature readingis to be taken.The thermocouple is then placed i

13、n the puddle of moltenmaterial.6.Keywords6.1 base;cavity;mold temperature;pyrometer1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.09 on Specimen Preparation.Current edition approved Nov.15,2012.Published December 2012.Ori

14、ginallyapproved in 1948.Last previous edition approved in 2006 as D957-06.DOI:10.1520/D0957-12.2NMI includes such organizations as the National Institute of Standards andTechnology.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO

15、Box C700,West Conshohocken,PA 19428-2959.United States1 SUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue(D957-06that may impact the use of this standard.(November 15,2012)(1)Revision of ISO equivalency statement.(2)Inclusion of use

16、 of non-contact pyrometers.(3)Removal of permissive language.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewe

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2