1、Designation:D9212bAmerican Association StateHighway and Transportation Officials StandardAASHTO No.:T48DIN 51 376Standard Test Method forFlash and Fire Points by Cleveland Open Cup Tester1This standard is issued under the fixed designation D92;the number immediately following the designation indicat
2、es the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.De
3、partment of Defense.INTRODUCTIONThis flash point and fire point test method is a dynamic method and depends on definite rates oftemperature increases to control the precision of the test method.Its primary use is for viscousmaterials having flash point of 79C(175F)and above.It is also used to determ
4、ine fire point,whichis a temperature above the flash point,at which the test specimen will support combustion for aminimum of 5 s.Do not confuse this test method with Test Method D4206,which is a sustainedburning test,open cup type,at a specific temperature of 49C(120F).Flash point values are a func
5、tion of the apparatus design,the condition of the apparatus used,andthe operational procedure carried out.Flash point can therefore only be defined in terms of a standardtest method,and no general valid correlation can be guaranteed between results obtained by differenttest methods,or with test appa
6、ratus different from that specified.1.Scope*1.1 This test method describes the determination of the flashpoint and fire point of petroleum products by a manualCleveland open cup apparatus or an automated Cleveland opencup apparatus.NOTE1The precisions for fire point were not determined in thecurrent
7、 interlaboratory program.Fire point is a parameter that is notcommonly specified,although in some cases,knowledge of this flamma-bility temperature may be desired.1.2 This test method is applicable to all petroleum productswith flash points above 79C(175F)and below 400C(752F)except fuel oils.NOTE2Th
8、is test method may occasionally be specified for thedetermination of the fire point of a fuel oil.For the determination of theflash points of fuel oils,use Test Method D93.Test Method D93 shouldalso be used when it is desired to determine the possible presence of small,but significant,concentrations
9、 of lower flash point substances that mayescape detection by Test Method D92.Test Method D1310 can beemployed if the flash point is known to be below 79C(175F).1.3 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 WARNINGMercu
10、ry has been designated by manyregulatory agencies as a hazardous material that can causecentral nervous system,kidney and liver damage.Mercury,orits vapor,may be hazardous to health and corrosive tomaterials.Caution should be taken when handling mercury andmercury containing products.See the applica
11、ble product Ma-terial Safety Data Sheet(MSDS)for details and EPAswebsitehttp:/www.epa.gov/mercury/faq.htmfor addi-tional information.Users should be aware that selling mercuryand/or mercury containing products into your state or countrymay be prohibited by law.1.5 This standard does not purport to a
12、ddress all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For specificwarning statements,see 6.4,7.1,11.1.3,and 11.
13、2.4.1This test method is under the joint jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.08 on Volatility.In the IP,this test method is under thejurisdiction of the Standardization Committee.This test method was
14、adopted as ajoint ASTM-IP standard in 1965.Current edition approved Dec.1,2012.Published March 2013.Originallyapproved in 1921.Last previous edition approved in 2012 as D9212a.DOI:10.1520/D0092-12B.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr
15、 Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.Referenced Documents2.1 ASTM Standards:2D93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD140 Practice for Sampling Bituminous MaterialsD1310 Test Method for Flash Point and Fire Point of Liquidsby Tag Open-
16、Cup ApparatusD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4206 Test Method for Sustained Burning of Liquid Mix-tures Using the Small Scale Open-Cup ApparatusE1 Specification for ASTM Liquid-in-Glass ThermometersE300 Practice for Sampling Industrial Chemicals2.2 Energy Institute Standard:3Specifications for IP Standard Thermometers2.3 ISO Standards:4Guide 34 Quality Systems Guidelines for the Producti