ImageVerifierCode 换一换
格式:PDF , 页数:10 ,大小:884.11KB ,
资源ID:168441      下载积分:8 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/168441.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_E_1077_-_14.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_E_1077_-_14.pdf

1、Designation:E107714Standard Test Methods forEstimating the Depth of Decarburization of SteelSpecimens1This standard is issued under the fixed designation E1077;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision

2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.INTRODUCTIONThese test methods may be used to estimate the ave

3、rage or greatest depth of decarburization inhardened or non-hardened steel products.The test methods described range from simple screeningtests to more statistically rigorous test methods depending upon the needs of the investigation.1.Scope1.1 These test methods cover procedures for estimating thed

4、epth of decarburization of steels irrespective of thecomposition,matrix microstructure,or section shape.Thefollowing basic procedures may be used:1.1.1 Screening methods.1.1.2 Microscopical methods.1.1.3 Microindentation hardness methods.1.1.4 Chemical analysis methods.1.2 In case of a dispute,the r

5、igorous quantitative or linealanalysis method(see 7.3.5 and 7.3.6)shall be the refereemethod.These methods can be employed with any cross-sectional shape.The chemical analytical methods generallyreveal a greater depth of decarburization than the microscopi-cal methods but are limited to certain simp

6、le shapes and byavailability of equipment.These techniques are generallyreserved for research studies.The microindentation hardnessmethod is suitable for accurate measurements of hardenedstructures with relatively homogeneous microstructures.1.3 The values stated in SI units are to be regarded assta

7、ndard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica

8、-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A941 Terminology Relating to Steel,Stainless Steel,RelatedAlloys,and FerroalloysE3 Guide for Preparation of Metallographic SpecimensE7 Terminology Relating to MetallographyE340 Test Method for Macroetching Metal

9、s and AlloysE350 Test Methods for Chemical Analysis of Carbon Steel,Low-Alloy Steel,Silicon Electrical Steel,Ingot Iron,andWrought IronE384 Test Method for Knoop and Vickers Hardness ofMaterialsE407 Practice for Microetching Metals and AlloysE415 Test Method for Analysis of Carbon and Low-AlloySteel

10、 by Spark Atomic Emission SpectrometryE1951 Guide for Calibrating Reticles and Light MicroscopeMagnifications3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in these test methods,seeTerminology E7 and Terminology A941.3.2 Definitions of Terms Specific to This Standard:3.2.1 average

11、depth of decarburizationthe mean value offive or more measurements of the total depth of decarburiza-tion.3.2.2 average free-ferrite depththe mean value of five ormore measurements of the depth of complete decarburization.1These test methods are under the jurisdiction of ASTM Committee E04 onMetallo

12、graphy and are the direct responsibility of Subcommittee E04.14 onQuantitative Metallography.Current edition approved Jan.1,2014.Published March 2014.Originallyapproved in 1985.Last previous edition approved in 2005 as E1077 01(2005).DOI:10.1520/E1077-14.2For referenced ASTM standards,visit the ASTM

13、 website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3

14、.2.3 complete decarburizationloss of carbon content atthe surface of a steel specimen to a level below the solubilitylimit of carbon in ferrite so that only ferrite is present.3.2.4 free-ferrite depththe perpendicular distance from thesurface of the specimen to that location where the structure isno

15、 longer fully ferritic,that is,other transformation productsare observed.NOTE1The term free ferrite has also been used to describe globular,isolated grains of proeutectoid ferrite in the microstructure of medium-carbon hypoeutectoid steels.3.2.5 maximum depth of decarburizationthe largest mea-sured

16、value of the total depth of decarburization.3.2.6 partial decarburizationloss of carbon content at thesurface of a steel specimen to a level less than the bulk carboncontent of the unaffected interior but greater than the roomtemperature solubility limit of carbon in ferrite.3.2.7 total depth of decarburizationthe perpendicular dis-tance from the specimen surface to that location in the interiorwhere the bulk carbon content is reached;that is,the sum of thedepths of complete and partial decarbur

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2