1、Designation:E109599(Reapproved 2010)Standard Specification forCommon Laboratory Glass Funnels1This standard is issued under the fixed designation E1095;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe
2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers common laboratory or filterfunnels,and filling or powder funnels for general laboratoryuse.1.2 The values stated in SI
3、 units are to be regarded asstandard.No other units of measurement are included in thisstandard.2.Referenced Documents2.1 ASTM Standards:2E438 Specification for Glasses in Laboratory ApparatusE671 Specification for Maximum Permissible Thermal Re-sidual Stress in Annealed Glass Laboratory ApparatusE9
4、20 Specification for Commercially Packaged LaboratoryApparatusE921 Specification for Export Packaged Laboratory Appa-ratusE1133 Practice for Performance Testing of Packaged Labo-ratory Apparatus for United States Government Procure-mentsE1157 Specification for Sampling and Testing of ReusableLaborat
5、ory Glassware3.Classification3.1 There shall be four types of laboratory glass funnelsfurther divided into classes.3.1.1 Type 1Common laboratory funnel with smooth innersurface,divided into the following three classes:3.1.1.1 Class A,(short stem)Sizes 25,35,45,55,65,75,90,100,125,and 150-mm diameter
6、s.3.1.1.2 Class B,(long stem)Sizes 35,45,50,55,65,75,90,100,125,150,200,250,and 300-mm diameters.3.1.1.3 Class C,(without stem)Sizes 50,75,and 100-mmdiameters.3.1.2 Type 2Laboratory funnel with fluted inner wall.Theflutes are small grooves or depressions running upward fromthe bottom zone of the bow
7、l.3.1.2.1 Class A,(short stem)Sizes 50,65,75,and 100-mmdiameters.3.1.2.2 Class B,(long stem)Sizes 50,65,75,and 100-mmdiameters.3.1.3 Type 3Laboratory funnel with ribbed inner wall.Theribs are small raised protuberances running from funnel rimtoward the stem.3.1.3.1 Class A,(short stem)Sizes 50,65,75
8、,and 100-mmdiameters.3.1.3.2 Class B,(long stem)Sizes 50,65,75,and 100-mmdiameters.3.1.4 Type 4Filling or powder funnels.3.1.4.1 Short,Wide Diameter StemSizes 60,65,75,80,100,125,and 150-mm diameters.4.Material and Annealing4.1 MaterialFunnels shall be made of glass conforming tothe requirement of T
9、ype 1,Class A or B or Type 2 ofSpecification E438.4.2 AnnealingMaximum residual stress shall be such as toconform to Specification E671.5.Design5.1 BowlThe inner wall of the bowl shall diverge from thestem at an angle of 30 6 1.2.The bowl shall be securelysealed to the stem.The axis of the funnel bo
10、wl shall coincidewith the stem axis and the rim shall be perpendicular to thisaxis.The edge of the rim shall be mold finish,beaded orground to a horizontal surface,as specified.5.1.1 Type 1Bowl of common funnels shall be plain.5.1.2 Type 1,Class CBottom of bowl shall be ground flat.5.1.3 Type 2Bowl
11、of fluted funnels shall have an innerwall with 8 equally spaced small grooves or depressions thatshall extend upward from the inner bottom zone of the bowl12to58times the inner bowl depth.5.1.4 Type 3Bowl of ribbed funnel shall have an innerwall with raised ribs spaced at the rim approximately 15 mm
12、apart.Alternate ribs shall extend to within approximately 6 mmof the junction of the bowl and the stem,and the others towithin approximately 19 mm of this junction.Ribbed funnelsmay also have ribs on the outer bowl surface or stem,or both.1This specification is under the jurisdiction of ASTM Committ
13、ee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onApparatus.Current edition approved Sept.1,2010.Published September 2010.Originallyapproved in 1986.Last previous edition approved in 2005 as E1095 99(2005).DOI:10.1520/E1095-99R10.2For referenced ASTM standards,v
14、isit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Uni
15、ted States1 If the outer bowl surface is ribbed,there must be at least threeribs evenly spaced around the bowl.5.2 Stem:5.2.1 Types 1,Class A and B;Type 2;and Type 3The stemshall have an oblique termination of not less than 30,smoothly ground to a level point or fire polished.The stemshall have para
16、llel sides,or a straight taper if drawn out of thebowl.The diameter of the stem at the bowl juncture shall besmall enough so that the stem will fill readily but not so smallas to retard the rate of flow in ordinary filtrations.The diameterat the end of the stem shall be small enough so that the columnof filtrate will not break.(Both diameter requirements refer touse with water or dilute aqueous solutions.)5.2.2 Type 3Stem of Type 3 funnels may be ribbed on theouter wall.If so,the ribs must be di