ImageVerifierCode 换一换
格式:PDF , 页数:6 ,大小:177.44KB ,
资源ID:168574      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/168574.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_E_1603_-_E_1603M_-_11.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_E_1603_-_E_1603M_-_11.pdf

1、Designation:E1603/E1603M11Standard Practice forLeakage Measurement Using the Mass Spectrometer LeakDetector or Residual Gas Analyzer in the Hood Mode1This standard is issued under the fixed designation E1603/E1603M;the number immediately following the designation indicates the yearof original adopti

2、on or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers procedures for testing the sourcesof gas leaking at the ra

3、te of 1 108Pa m3/s(1 109standard-cm3/s at 0C)or greater.These test methods may beconducted on any object that can be evacuated and to the otherside of which helium or other tracer gas may be applied.Theobject must be structurally capable of being evacuated topressures of 0.1 Pa(approximately 103torr

4、).1.2 Three test methods are described;1.2.1 Test Method AFor the object under test capable ofbeing evacuated,but having no inherent pumping capability.1.2.2 Test Method BFor the object under test with integralpumping capability.1.2.3 Test Method CFor the object under test as in TestMethod B,in whic

5、h the vacuum pumps of the object under testreplace those normally used in the leak detector(LD).1.3 UnitsThe values stated in either SI or std-cc/sec unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents:therefore,eachsystem shall be used indepen

6、dently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and hea

7、lth practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E1316 Terminology for Nondestructive Examinations2.2 ASNT Standards:3SNT-TC-1A Recommended Practice for Personnel Qualifi-cation and Certification in Nondestructive Testing

8、ANSI/ASNT-CP-189 Standard for Qualification and Certifi-cation of Nondestructive Testing Personnel2.3 Military Standard:MIL-STD-410 Nondestructive Testing Personnel Qualifica-tion and Certification42.4 AIA Standard:NAS-410 Certification and Qualification of NondestructiveTest Personnel53.Terminology

9、3.1 DefinitionsFor definitions of terms used in thispractice,see Terminology E1316.4.Summary of Practice4.1 These test methods covered in this practice require ahelium LD that can provide a system sensitivity of 10%or lessof the intended leakage rate to be measured.4.2 Test Method AThis test method

10、is used to helium leaktest objects that are capable of being evacuated to a reasonabletest pressure by the LD pumps during an acceptable length oftime(see Fig.1).This requires that the object be clean and dry.Auxiliary vacuum pumps having greater capacity than those inthe LD may be used in conjuncti

11、on with them.The leak testsensitivity will be reduced under these conditions.4.3 Test Method BThis test method is used to leak testequipment that can provide its own vacuum(that is,equipmentthat has a built-in pumping system)at least to a level of a fewhundred pascals(a few torr)or lower.Refer to Fi

12、g.2.4.4 Test Method CWhen a vacuum system is capable ofproducing internal pressures of less than 2 102Pa(2 104torr)in the presence of leaks,these leaks may be located and1This practice is under the jurisdiction of ASTM Committee E07 on Nonde-structive Testing and is the direct responsibility of Subc

13、ommittee E07.08 on LeakTesting Method.Current edition approved July 1,2011.Published July 2011.Originally approvedin 1994.Last previous edition approved in 2006 as E1603-99(2006).DOI:10.1520/E1603_E1603M-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Se

14、rvice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available fromAmerican Society for Nondestructive Testing(ASNT),P.O.Box28518,1711 Arlingate Ln.,Columbus,OH 43228-0518,http:/www.asnt.org.4Available from Stan

15、dardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.5Available from Aerospace Industries Association of America,Inc.(AIA),1000Wilson Blvd.,Suite 1700,Arlington,VA22209-3928,http:/www.aia-aerospace.org.*A Summary of Changes sectio

16、n appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 evaluated by the use of either a residual gas analyzer(RGA)orby using the spectrometer tube and controls from a conven-tional MSLD,provided that the leakage is within the sensitivityrange of the RGAor MSLD under the conditions existing in thevacuum system.Refer to Fig.3.5.Significance and Use5.1 Test Method AThis test method is the most frequentlyused

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2