1、Designation:E136318Standard Test Method forTemperature Calibration of Thermomechanical Analyzers1This standard is issued under the fixed designation E1363;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A nu
2、mber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method describes the temperature calibrationof thermomechanical analyzers from 50 C to 1500 C.(SeeNote 1.)1.2 The values stated in
3、 SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 WarningMercury has been designated by many regu-latory agencies as a hazardous substance that can causeserious medical issues.Mercury,or its vapor,has beendemonstrated to be hazardous to health and
4、 corrosive tomaterials.Use caution when handling mercury and mercury-containing products.See the applicable product Safety DataSheet(SDS)for additional information.The potential existsthat selling mercury or mercury-containing products,or both,is prohibited by local or national law.Users must determ
5、inelegality of sales in their location.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of r
6、egulatory limitations prior to use.Specific precautionary statements are given in Section 7 andNote 11.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of Internati
7、onal Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E473 Terminology Relating to Thermal Analysis and Rhe-ologyE3142 Test Method for Thermal Lag of Thermal AnalysisApparatus3.Terminology3
8、.1 Definitions:3.1.1 The terminology relating to thermal analysis appear-ing in Terminology E473 shall be considered applicable to thisdocument.4.Summary of Test Method4.1 An equation is developed for the linear correlation of theexperimentally observed program temperature and the actualmelting temp
9、erature for known melting standards.This isaccomplished through the use of a thermomechanical analyzerwith a penetration probe to obtain the onset temperatures fortwo melting point standards.An alternate,one-point method oftemperature calibration is also given for use over very narrowtemperature ran
10、ges.(See Note 2.)NOTE1This test method may be used for calibrating thermomechani-cal analyzers at temperatures outside this range of temperature.However,the accuracy of the calibration will be no better than that of thetemperature standards used.NOTE2It is possible to develop a more elaborate method
11、 oftemperature calibration using multiple(more than two)fusion standardsand quadratic regression analysis.Since most modern instruments arecapable of heating rates which are essentially linear in the region of use,the procedure given here is limited to a two-point calibration.5.Significance and Use5
12、.1 Thermomechanical analyzers are employed in theirvarious modes of operation(penetration,expansion,flexure,etc.)to characterize a wide range of materials.In most cases,the value to be assigned in thermomechanical measurements isthe temperature of the transition(or event)under study.Therefore,the te
13、mperature axis(abscissa)of all TMA thermal1This test method is under the jurisdiction ofASTM Committee E37 on ThermalMeasurements and is the direct responsibility of Subcommittee E37.10 onFundamental,Statistical and Mechanical Properties.Current edition approved Dec.1,2018.Published January 2019.Ori
14、ginallyapproved in 1990.Last previous edition approved in 2016 as E1363 16.DOI:10.1520/E1363-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Su
15、mmary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principle
16、s on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 curves must be accurately calibrated either by direct reading ofa temperature sensor or by adjusting the programmer tempera-ture to match the actual temperature over the temperature rangeof interest.6.Apparatus6.1 Thermomechanical Analyzer(TMA)The essential in-strumentation requir