1、Designation:E 1147 92(Reapproved 2005)Standard Test Method forPartition Coefficient(N-Octanol/Water)Estimation by LiquidChromatography1This standard is issued under the fixed designation E 1147;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes a procedure for the estima-tion of the log of the octanol/water partition
3、coefficient(logKow)of chemicals over the range from 0 to 8.1.2 This test method uses an empirically derived equation torelate the octanol/water partition coefficient to an experimen-tally determined retention time on a liquid chromatographiccolumn.1.3 This test method has been designed to estimate l
4、ogKowvalues for both non-ionizable and ionizable compounds.This is accomplished by buffering the liquid chromatographicsolvent at a pH that will force the test compound into either thenon-ionized or ionized form.1.4 This test method requires some knowledge of thedetector response to the chemical bei
5、ng tested.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish safetyand health practices and determine the applicability of regu-latory limitations prior to use.2.Referenced Documents
6、2.1 ASTM Standards:2D 1193 Specification for Reagent WaterE 200 Practice for Preparation,Standardization,and Stor-age of Standard Solutions for Chemical AnalysisE 682 Practice for Liquid Chromatography Terms and Re-lationshipsE 1022 Practice for Conducting Bioconcentration Tests withFishes and Saltw
7、ater Bivalve Molluscs3.Terminology3.1 Definitions:3.1.1 octanol/water partition coeffcient(Kow)the equilib-rium ratio of the molar concentrations of a chemical inn-octanol and water,in dilute solution.Kowis a constant for aspecific chemical at a given temperature.Since Kowis the ratioof two molar co
8、ncentrations,it is a dimensionless quantity.Kowis often reported as log Kow.3.1.2 retention time(tR,to)the reference compound or testchemical retention time(tR)is the time from sample injectionto maximum concentration(peak height)of eluted referencecompound or test chemical.The internal standard ret
9、entiontime(to)is the time from sample injection to the maximumconcentration(peak height)of the eluted internal standard.4.Summary of Test Method4.1 This test method is based on the work of Veith et al(1).3Another similar test method is available from OECD(2).4.2 The test substance(solute)is injected
10、 onto a liquidchromatograph column containing a solid-phase support ontowhich a commercially available long-chain hydrocarbon(forexample C8 or C18)has been bonded.Chemicals injected ontosuch a column move along it by partitioning between themobile phase and the stationary hydrocarbon phase.Amethanol
11、/water solvent system is typically used to elute thesolute which is subsequently analyzed using an ultraviolet/visible absorption detector,refractive index detector,electro-chemical detector,or other appropriate detector.If the testsubstance is not amenable to detection by the available LCdetectors,
12、the analyst may collect fractions of the columneffluent and analyze for the test substance using gas chroma-tography,liquid scintillation,or other appropriate technique.4.3 The Kowof the test compound is estimated from a linearregression equation developed from a plot of log(tR to)versuslog Kow,usin
13、g data determined in a calibration step thatinvolves injecting into the chromatograph a mixture of refer-ence chemicals.4.4 A calibration graph of log(tR to)versus log Kowisdeveloped for a number of reference compounds(typicallybetween 5 and 10)which are structurally similar to the testchemical.List
14、s of values of measured log Koware available for1This test method is under the jurisdiction of ASTM Committee E47 onBiological Effects and Environmental Fate and is the direct responsibility ofSubcommittee E47.04 on Environmental Fate of Chemical Substances.Current edition approved August 1,2005.Pub
15、lished August 2005.Originallyapproved in 1987.Last previous edition approved in 1997 as E 1147 87(1997).2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Doc
16、ument Summary page onthe ASTM website.3The boldface numbers in parentheses refer to the list of references at the end ofthis test method.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.many chemicals(3,4,5).If data on the partition coefficients ofstructurally related compounds are not available,a moregeneral calibration graph must be developed using otherreference compounds.This is a less accurate approach than thatusing partition coe