ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:81.51KB ,
资源ID:169265      下载积分:12 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/169265.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_E_2425_-_16.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_E_2425_-_16.pdf

1、Designation:E242516Standard Test Method forLoss Modulus Conformance of Dynamic MechanicalAnalyzers1This standard is issued under the fixed designation E2425;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A

2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method describes the performance confirma-tion or measurement of conformance for the loss modulus scaleof a commercial or custom

3、-built dynamic mechanical analyzer(DMA)at 21C using ultra-high molecular weight polyethyl-ene as a reference material.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 There is no ISO standard equivalent to this test method

4、.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2.Referenced Doc

5、uments2.1 ASTM Standards:2E473 Terminology Relating to Thermal Analysis and Rhe-ologyE1142 Terminology Relating to Thermophysical PropertiesE1867 Test Methods for Temperature Calibration of Dy-namic Mechanical Analyzers3.Terminology3.1 DefinitionsSpecific technical terms used in this testmethod are

6、defined in Terminologies E473 and E1142 includ-ing Celsius,dynamic mechanical analysis,and loss modulus.4.Summary of Test Method4.1 The loss modulus signal measured by a dynamic me-chanical analyzer for an elastic material is compared to thereported loss modulus for that reference material.A linearr

7、elationship is used to correlate the experimental loss modulussignal with the reported value of the reference material.4.2 The mode of deformation(for example,tensile,flexure,compression,shear,etc.)shall be reported.5.Significance and Use5.1 This test method demonstrates conformity of a dynamicmecha

8、nical analyzer at an isothermal temperature of 21C.5.2 Dynamic mechanical analysis experiments often uselinear temperature change.This test method does not addressthe effect of that change in temperature on the loss modulus.5.3 This test method may be used in research anddevelopment,specification ac

9、ceptance,and quality control orassurance.6.Apparatus6.1 The essential instrumentation required to provide theminimum dynamic mechanical capability for this test methodincludes:6.1.1 Drive Actuator,to apply force(or displacement)to thespecimen in a periodic manner.This actuator may also becapable of

10、providing static force or displacement to thespecimen.6.1.2 Coupling Shaft,or other means to transmit the forcefrom the motor to the specimen.6.1.3 Clamping System(s),to fix the specimen between thedrive shaft and the stationary clamp(s).6.1.4 Position Sensor,to measure the change in position ofthe

11、specimen during dynamic motion,or6.1.5 Force Sensor,to measure the force developed by thespecimen.6.1.6 Temperature Sensor,to provide an indication of thespecimen temperature to within 61C.6.1.7 Furnace,to provide controlled heating or cooling of aspecimen at a constant temperature or at a constant

12、rate withinthe applicable temperature range of 100 to+300C.6.1.8 Temperature Controller,capable of executing a spe-cific temperature program by operating the furnace between100 and+300C and at a constant temperature within thatrange.1This test method is under the jurisdiction ofASTM Committee E37 on

13、 ThermalMeasurements and is the direct responsibility of Subcommittee E37.10 onFundamental,Statistical and Mechanical Properties.Current edition approved June 1,2016.Published June 2016.Originallyapproved in 2005.Last previous edition approved in 2011 as E2425 11.DOI:10.1520/E2425-16.2For referenced

14、 ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM I

15、nternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.1.9 Data Collection Device,to provide a means ofacquiring,storing,and displaying measured or calculatedsignals,or both.The minimum output signals required fordynamic mechanical analysis are storage modulu

16、s,lossmodulus,tan delta,temperature,and time.6.2 Auxiliary instrumentation considered necessary in con-ducting this method near or below ambient temperature:6.2.1 Cooling capability to sustain a constant temperature ator below ambient temperature or to provide controlled cooling.6.2.2 Data Analysis capability to provide loss modulusinformation derived from measured signals.7.Reagents and Materials7.1 A reference material of known loss modulus,formed tothe shape suitable for characterization by t

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2