1、Designation:D784914Standard Classification forNomenclature of Reference Materials of Committee D241This standard is issued under the fixed designation D7849;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This classification covers instructions for naming thereference materials used by Committee D24.1.2 This standard does not purport to addre
3、ss all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1510 Test Method f
4、or Carbon BlackIodine AdsorptionNumberD2414 Test Method for Carbon BlackOil AbsorptionNumber(OAN)D3265 Test Method for Carbon BlackTint StrengthD3493 Test Method for Carbon BlackOil AbsorptionNumber of Compressed Sample(COAN)D6556 Test Method for Carbon BlackTotal and ExternalSurface Area by Nitroge
5、n Adsorption3.Significance and Use3.1 Standard reference materials are used for calibration andverification of many carbon black tests under the jurisdiction ofD24.This practice defines a systematic means of naming thesereference materials and does so in a manner to clearlydifferentiate between the
6、various reference materials as well astheir version.4.Basis of Classification4.1 ASTM Committee D24 has established four differenttypes of reference materials which serve to improve testprecision of analytical tests on carbon black as well asin-rubber evaluation of carbon black.34.1.1 SRB(Standard R
7、eference Blacks)A set of sevencarbon blacks,six furnace blacks with defined target values foriodine adsorption number(Test Method D1510),STSA(TestMethod D6556),NSA(Test Method D6556),OAN(TestMethod D2414),COAN(Test Method D3493)and TintStrength(Test Method D3265)and one thermal black withdefined val
8、ues for STSA(Test Method D6556),NSA(TestMethod D6556)and OAN(Test Method D2414).The SRBscan be used to verify analytical test equipment and testprocedures.For OAN and COAN,their application is manda-tory to normalize measured data.4.1.2 ITRB(Industry Tint Reference Black)ITRB repre-sents a standard
9、carbon black of the N330 type.It is used forverification and standardization in the test method for TintStrength(Test Method D3265).4.1.3 INR(Iodine Number Reference,previously designated“HT”)INR consist of three different reference blacks whichhave been heat-treated in order to provide particularly
10、 highstability of the iodine number over a long period of time,thatis,over many years.4.1.4 IRB(Industry Reference Black)IRB is a carbonblack of the N330 type which is produced in large quantities inorder to serve as a reference material in rubber compounds.In-rubber properties of this reference bla
11、ck are determinedduring a round robin tests when the material is introduced.4.2 Nomenclature:4.2.1 All letters in the designation are in caps with no spacesor special characters used.4.2.2 The reference material is identified by its type:SRB,ITRB,INR or IRB.4.2.3 The set number follows,with no speci
12、al characters orspace as separator,for example:SRB8.4.2.4 In the case where several materials form a set(likeSRB and INR),a letter is added,starting with A in ascendingorder(for example,SRB8A).Preferably the order of the1This classification is under the jurisdiction of ASTM Committee D24 onCarbon Bl
13、ack and is the direct responsibility of Subcommittee D24.41 on CarbonBlack Nomenclature and Terminology.Current edition approved June 1,2014.Published June 2014.DOI:10.1520/D7849-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.
14、For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Target values and control limits are published on the website of the distributorof these reference materials,Balentine Enterprise Inc.:http:/ ASTM International,100 Barr Harbor Drive,
15、PO Box C700,West Conshohocken,PA 19428-2959.United States1 materials is in line with a relevant property,like iodineadsorption number for INR.4.2.5 It may occur that a second lot of the same material isproduced after depletion of the initial lot.In order to distin-guish between both lots,a number is
16、 added in chronologicalorder,for example:SRB8A2(second lot of SRB8A).NOTE1While the same letters will be used from one set to the next,the materials carrying the same letter designation may or may not be thesame carbon black.4.3 Examples of how to identify reference materials follow:4.3.1 IRB and ITRB:4.3.1.1 The IRB currently in use in 2013 is identified asIRB8.4.3.1.2 The next IRB in the series will be identified as IRB9.4.3.1.3 The ITRB currently in use in 2013 is identified asITRB since this