1、Designation:D701920Standard Performance Specification forBrassiere,Slip,Lingerie and Underwear Fabrics1This standard is issued under the fixed designation D7019;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This performance specification covers fabrics used inbrassieres underwear,slips,and lingerie.1.2 These requirements apply to the length
3、 and widthdirections for those properties where each fabric direction ispertinent.1.3 The following safety hazards caveat pertains only to thetest methods described in this performance specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It
4、 is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standa
5、rd-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD434 Test Meth
6、od for Resistance to Slippage of Yarns inWoven Fabrics Using a Standard Seam(Withdrawn2003)3D1336 Test Method for Distortion of Yarn in Woven FabricsD1424 Test Method for Tearing Strength of Fabrics byFalling-Pendulum(Elmendorf-Type)ApparatusD2261 Test Method for Tearing Strength of Fabrics by theTo
7、ngue(Single Rip)Procedure(Constant-Rate-of-Extension Tensile Testing Machine)D3786 Test Method for Bursting Strength of TextileFabricsDiaphragm Bursting Strength Tester MethodD3787 Test Method for Bursting Strength of TextilesConstant-Rate-of-Traverse(CRT)Ball Burst TestD5034 Test Method for Breakin
8、g Strength and Elongation ofTextile Fabrics(Grab Test)D7022 Terminology Relating to Apparel2.2 AATCC Test Methods:4TM8 Colorfastness to Crocking:Crockmeter MethodTM15 Colorfastness to PerspirationTM16.3 Colorfastness to LightTM23 Colorfastness to Burnt Gas FumesTM61 Colorfastness to Laundering:Accel
9、eratedTM116 Colorfastness to Crocking:Rotary Vertical Crock-meter MethodTM124 Smoothness Appearance of Fabrics after RepeatedHome LaunderingTM132 Colorfastness to DrycleaningTM135 Dimensional Changes of Fabrics after Home Laun-deringTM158 Dimensional Changes on Drycleaning in Perchloro-ethylene:Mach
10、ine MethodTM172 Colorfastness to Powdered Non-Chlorine Bleach inHome LaunderingTM188 Colorfastness to Sodium Hypochlorite Bleach inHome Laundering2.3 Federal Standard:516 CFR 1610-Flammable Fabrics Act RegulationsNOTE1Reference to test methods in this specification give only thepermanent part of the
11、 designation of ASTM,AATCC,or other testmethods.The current editions of each test method cited shall prevail.3.Terminology3.1 For definitions of textile terms used in this specificationrefer to Terminologies D123 and D7022.For terms relating tochemical and colorfastness testing refer to specificAATC
12、C testmethods.3.2 Definitions found in a dictionary of common usage aresuitable for this specification.1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the direct responsibility of Subcommittee D13.61 on Apparel.Current edition approved July 1,2020.Published Augu
13、st 2020.Originallyapproved in 2005.Last previous edition approved in 2014 as D7019-14.DOI:10.1520/D7019-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards
14、Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Association of Textile Chemists and Colorists,P.O.Box 12215,Research Triangle Park,NC 27709.5Available from Superintendent of Documents,Government Pri
15、nting Office,Washington,DC 20402.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles
16、 for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.4.Significance and Use4.1 Fabrics intended for this end-use should meet all of therequirements listed in Table 1.4.2 It should be recognized that fabric can be producedutilizing an almost infinite number of combinations of con-struction variables(e.g.,type of fibers,percentage of fibers,yarn twist,yarn number,warp and pick count,chemical andme