1、Designation:D710812(Reapproved 2018)Standard Guide forEstablishing Qualifications for a Nuclear CoatingsSpecialist1This standard is issued under the fixed designation D7108;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide delineates recommendations for develop-ment of procedures and criteria for designation of an individualas a Nucl
3、ear Coatings Specialist involved in coating work innuclear facilities.The Nuclear Coatings Specialist is respon-sible for the technical aspects of the safety-related coatingsprogram in a nuclear facility or organization,which includesestablishing processes and quality control requirements.1.2 This g
4、uide details the guidance provided in GuideD5144,and EPRI Report 1019157.1.3 It is the intent of this guide to provide several alterna-tives for designation of personnel as Nuclear Coatings Special-ists.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with it
5、s use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principl
6、es on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4537 Guide for Establishing Procedures
7、 to Qualify andCertify Personnel Performing Coating and Lining WorkInspection in Nuclear FacilitiesD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD5144 Guide for Use of Protective Coating Standards inNuclear Power Plants2.2 ANSI/ASME Codes and Standard
8、s:3ANSI/ASME N45.2.6 Qualifications of Inspection,Exami-nation and Testing Personnel for Nuclear Power Plants2.3 Electric Power Research Institute(EPRI):4EPRI Report 1019157 Guidance on Nuclear Safety-RelatedCoatings,Revision 2(formerly TR-109937 and 1003102),December 20092.4 Code of Federal Regulat
9、ions(CFR):510CFR21 Reporting of Defects and Nonconformance10CFR50.59 Changes,Tests and Experiments3.Terminology3.1 DefinitionsDefinitions for use with this standard areshown in Terminology D4538 or other applicable standards.3.2 Definitions of Terms Specific to This Standard:3.2.1 safety-related coa
10、tings program,nthe systematicand planned activities conducted at a nuclear power plant toensure that the safety-related coatings and linings perform allof their design functions.4.Significance and Use4.1 This guide applies to personnel technically responsiblefor the safety-related coatings program.4
11、.2 It is the responsibility of each nuclear facility ororganization participating in a safety-related coatings programto ensure that only those personnel within their respectiveorganizations who meet the requirements of this guide aredesignated as Nuclear Coatings Specialists.5.General Duties and Re
12、sponsibilities of a NuclearCoatings Specialist5.1 The duties of a Nuclear Coatings Specialist should bedetailed in the facility safety-related coatings program andtypically may include,but are not limited to:1This guide is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining
13、Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.04 on Quality Systems and Inspection.Current edition approved Aug.15,2018.Published November 2018.Originallyapproved in 2005.Last previous edition approved in 2012 as D7108 12.DOI:10.1520/D7108-12R18.2For refere
14、nced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th
15、 Floor,New York,NY 10036,http:/www.ansi.org.4Available from Electric Power Research Institute,3420 Hillview Ave.,PaloAlto,CA 94304,http:/.5Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.Copyrig
16、ht ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.1.1 Developing and managing the safety-related coatingsprogram,5.1.2 Developing a