1、Designation:D7332/D7332M15AStandard Test Method forMeasuring the Fastener Pull-Through Resistance of aFiber-Reinforced Polymer Matrix Composite1This standard is issued under the fixed designation D7332/D7332M;the number immediately following the designation indicates theyear of original adoption or,
2、in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method determines the fastener pull-throughresistance of multidirectional pol
3、ymer matrix composites rein-forced by high-modulus fibers.Fastener pull-through resis-tance is characterized by the force-versus-displacement re-sponse exhibited when a mechanical fastener is pulled througha composite plate,with the force applied perpendicular to theplane of the plate.The composite
4、material forms are limited tocontinuous-fiber or discontinuous-fiber(tape or fabric,or both)reinforced composites for which the laminate is symmetric andbalanced with respect to the test direction.The range ofacceptable test laminates and thicknesses is defined in 8.2.1.2 Two test procedures and con
5、figurations are provided.The first,Procedure A,is suitable for screening and fastenerdevelopmentpurposes.Thesecond,ProcedureB,isconfiguration-dependent and is suitable for establishing designvalues.Both procedures can be used to perform comparativeevaluations of candidate fasteners/fastener system d
6、esigns.1.3 The specimens described herein may not be representa-tive of actual joints which may contain one or more free edgesadjacent to the fastener,or may contain multiple fasteners thatcan change the actual boundary conditions.1.4 This test method is consistent with the recommendationsof CMH-17,
7、which describes the desirable attributes of afastener pull-through test method.1.5 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system are not exact equivalents;therefore,each systemmust be used independently of the other.
8、Combining valuesfrom the two systems may result in nonconformance with thestandard.1.5.1 Within the text the inch-pound units are shown inbrackets.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standa
9、rd to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to Plas
10、ticsD3171 Test Methods for Constituent Content of CompositeMaterialsD3410/D3410M Test Method for Compressive Properties ofPolymer Matrix Composite Materials with UnsupportedGage Section by Shear LoadingD3878 Terminology for Composite MaterialsD5229/D5229M Test Method for MoistureAbsorption Prop-erti
11、es and Equilibrium Conditioning of Polymer MatrixComposite MaterialsD5687/D5687M Guide for Preparation of Flat CompositePanels with Processing Guidelines for Specimen Prepara-tionE4 Practices for Force Verification of Testing MachinesE6 Terminology Relating to Methods of Mechanical TestingE18 Test M
12、ethods for Rockwell Hardness of Metallic Ma-terialsE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or ProcessE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE456 Terminology Relating to Quality and Statis
13、ticsE1309 GuideforIdentificationofFiber-ReinforcedPolymer-Matrix Composite Materials in DatabasesE1434 Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases1This test method is under the jurisdiction of ASTM Committee D30 onComposite Materials and is the direc
14、t responsibility of Subcommittee D30.05 onStructural Test Methods.Current edition approved May 15,2015.Published May 2015.Originallyapproved in 2007.Last previous edition approved in 2015 as D7332/D7332M15.DOI:10.1520/D7332_D7332M-15A.2For referenced ASTM standards,visit the ASTM website,www.astm.or
15、g,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.2 Industry Document
16、s:CMH-17-1G Composite Materials Handbook,Volume1Polymer Matrix Composites Guidelines for Character-ization of Structural Materials33.Terminology3.1 DefinitionsTerminology D3878 defines terms relatingto composite materials.Terminology D883 defines termsrelating to plastics.Terminology E6 defines terms relating tomechanical testing.Terminology E456 and Practice E177define terms relating to statistics.In the event of a conflictbetween terms,Terminology D3878 shall have precedenceover the other stan