1、Designation:D7016/D7016M20Standard Test Method toEvaluate Edge Binding Components Used in MattressesAfter Exposure to An Open Flame1This standard is issued under the fixed designation D7016/D7016M;the number immediately following the designation indicates theyear of original adoption or,in the case
2、of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONEvaluation of raw material components is a vital and ongoing part of any manufacturing operation,e
3、specially when each item can contribute to the technical performance of the final product.Components used in a mattress construction govern the ultimate product performance,its comfort anddurability,and also affect its flammability behavior.The textile components used on the exterior of the mattress
4、mattress tape and sewing threadarecritical for holding the structure together.These components contribute to the aesthetics of thestructure,and they are also susceptible to ignition when exposed to an open flame hazard.Data whichindicate that these two components are able to meet minimum performance
5、 criteria when exposed toan open flame provides the mattress manufacturers with valuable information.The value of these data increases when the behavior of components in a small scale test correlateto the behavior of these components in a full scale mattress burn test.The performance criteria requir
6、ethat:(1)the components do not support the combustion of the afterflame and,(2)that thesecomponents demonstrate post flame exposure characteristics which contribute to the retention ofstructural integrity and prevent seam rupture.This test method can be used as a quality controltechnique in a suppli
7、er quality assurance program.1.Scope1.1 This test method measures the flammability character-istics of mattress edge bindings and sewing threads during andafter exposure to an open flame ignition source.1.1.1 This test method is used to evaluate these componentseither independently or in combination
8、 for use in mattressesdesigned with a fire barrier fabric.1.1.1.1 The test method is used to evaluate mattress edgebinding and sewing thread when the design requires the use ofthese components.1.1.2 This test method can be used as a screening testmethod to determine how sewing thread and mattress ed
9、gebinding component combinations will perform.1.2 This standard is used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled conditions,but does not by itselfincorporate all factors required for fire hazard or fire riskassessment of the materials,
10、products,or assemblies underactual fire conditions.1.3 Fire testing of products and materials is inherentlyhazardous,and adequate safeguards for personnel and propertyshall be employed in conducting these tests.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately
11、 as standard.The values stated ineach system are not necessarily exact equivalents;therefore,toensure conformance with the standard,each system shall beused independently of the other,and values from the twosystems shall not be combined.1.5 This standard does not purport to address all of thesafety
12、concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with i
13、nternationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.1This test method is under the jurisdiction ofA
14、STM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.52 on Flammability.Current edition approved Aug.1,2020.Published September 2020.Originallyapproved in 2004.Last previous edition approved in 2018 as D701618.DOI:10.1520/D7016_D7016M-20.Copyright ASTM International,100
15、Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommen
16、dations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD204 Test Methods for Sewing ThreadsD1683 Test Method for Failure in Sewn Seams of WovenFabricsD4391 Terminology Relating to The Burning Behavior ofTextilesD7138 Test Method to Determine Melting Temperature ofSynthetic FibersD7140 Test Method to Measure Heat Transfer ThroughTextile Thermal Barrier Materials2.2 AATCC Method3AATCC