1、Designation:D760211(Reapproved 2017)Standard Practice forInstallation of Vulcanized Rubber Linings1This standard is issued under the fixed designation D7602;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers the techniques used to install rubberlining sheet stock in metal tanks,pipes,and other components.Installation require
3、ments,procedures,inspection instructions,and storage conditions for the lined tanks or equipment areoutlined.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are n
4、ot considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limita
5、tions prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization Te
6、chnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D429 Test Methods for Rubber PropertyAdhesion toRigid SubstratesD2240 Test Method for Rubber PropertyDurometer Hard-nessD4285 Test Method for Indicating Oil or Water in Com-pressed AirD4417 Test Methods for Field Measur
7、ement of SurfaceProfile of Blast Cleaned SteelD4538 Terminology Relating to Protective Coating andLining Work for Power Generation FacilitiesD5162 Practice for Discontinuity(Holiday)Testing of Non-conductive Protective Coating on Metallic SubstratesE1216 Practice for Sampling for Particulate Contami
8、nationby Tape Lift2.2 International Organization for Standardization:3ISO 8502-3 Preparation of Steel Substrates Before Applica-tion of Paints and Related ProductsTests for the Assess-ment of Surface CleanlinessPart 3:Assessment of Duston Steel Surfaces Prepared for Painting(Pressure-Sensitive Tape
9、Method)2.3 NACE Standards:4SP0178 Standard Recommended PracticeFabricationDetails,Surface Finish Requirements and Proper DesignConsiderations for Tanks and Vessels to be Lined forImmersion ServiceSP0188 Discontinuity(Holiday)Testing of New ProtectiveCoatings2.4 SSPC Standards:5SSPC-Technology Guide
10、15 Field Methods for Retrieval andAnalysis of Soluble Salts on Steel and Other NonporousSubstratesSSPC-SP 1 Solvent CleaningSSPC-SP 2 Hand Tool CleaningSSPC-SP 3 Power Tool CleaningSSPC-SP 5/NACE No.1 White Metal Blast CleaningSSPC-VIS 1 Guide and Reference Photographs for SteelSurfaces Prepared by
11、Dry Abrasive Blast Cleaning3.Terminology3.1 DefinitionsDefinitions for use with this standard areshown in Terminology D4538 or other applicable standards.3.2 Definitions of Terms Specific to This Standard:1This practice is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining
12、Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.09 on Protective Lining forAir Quality ControlSystems.Current edition approved Sept.1,2017.Published September 2017.Originallyapproved in 2011.Last previous edition approved in 2011 as D7602 11.DOI:10.1520/D7602
13、-11R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI)
14、,25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from NACE International(NACE),15835 Park Ten Pl.,Houston,TX77084,http:/www.nace.org.5Available from Society for Protective Coatings(SSPC),800 Trumbull Dr.,Pittsburgh,PA 15205,http:/www.sspc.org.Available from American Architect
15、uralManufacturers Association(AAMA),1827 Walden Office Square,Suite 550,Schaumburg,IL 60173-4268,http:/www.aamanet.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationa
16、lly recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.1 autoclave,na pressure vessel used for the curing orvulcanization of rubber parts by means of steam under pres-sure.3.2.2 blister,nan isolated convex deformation arisingfrom the detachment of one or more layers of lining material.3.2.3 bond failure,na