1、Designation:D733015Standard Test Method forAssessment of Surface Appearance Change in Pile FloorCoverings Using Standard Reference Scales1This standard is issued under the fixed designation D7330;the number immediately following the designation indicates the year oforiginal adoption or,in the case o
2、f revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1This test method covers the assessment of changes ofsurface appearance of pile floor coverings after
3、exposure toactual or simulated foot traffic.This test method applies to pileyarn floor coverings that are,or have been,installed;laboratoryfloor-trafficked samples;or textiles floor coverings traffickedby mechanical traffic simulators.The subjective assessment isfacilitated by use of reference scale
4、s that are based on digitalimages of representative pile yarn floor covering styles andconstructions.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not consi
5、dered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.R
6、eferenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD5252 Practice for the Operation of the Hexapod TumbleDrum TesterD5417 Practice for Operation of the Vettermann DrumTesterD5684 Terminology Relating to Pile Floor CoveringsD6119 Practice for Creating SurfaceAppearance Change
7、s inPile Yarn Floor Covering from Foot TrafficD6962 Practice for Operation of a Roller Chair Tester forPile Yarn Floor CoveringsE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.T
8、erminology3.1 For definitions of terms relating to Pile Floor Coverings,refer to the Terminology D5684.3.2 The following terms are relevant to this standard:carpet,crushing cut pile yarn floor covering,finished,finished pileyarn floor covering,loss of tuft definition,matting,pile,pileyarn floor cove
9、ring,textile floor covering.3.3 For definitions of other terms related to textiles,refer toTerminology D123.4.Summary of Test Method4.1 The floor covering shall be tested in a mechanical wearsimulator or tested under controlled laboratory foot traffic testsreferenced in Practices D5252,D5417,D6119,a
10、nd D6962.Thetested floor covering shall then be assessed for surface appear-ance change by comparing unexposed controls to the exposedsample by using the appropriate Appearance Change GradingScale.5.Significance and Use5.1 The determination of surface appearance change in pileyarn floor covering is
11、useful in quality and cost control duringmanufacture of pile yarn floor covering.This test method isconsidered satisfactory for acceptance testing of commercialshipments because current estimates of between laboratoryprecision are acceptable,and this test method is commonlyused in trade for acceptan
12、ce testing.5.2 If there are differences of practical significance betweenreported test results for two laboratories(or more),compara-tive test should be performed to determine if there is astatistical bias between them,using competent statistical assis-tance.As a minimum,use the samples for such com
13、parativetests that are as homogenous as possible,drawn from the samelot of material as the samples that resulted is desparate resultsduring initial testing and randomly assigned in equal numbersto each laboratory.The test results from the laboratories1This test method is under the jurisdiction ofAST
14、M Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.21 on Pile Floor Coverings.Current edition approved Feb.1,2015.Published April 2015.Originallyapproved in 2007 as D7330-07.Last previous edition published in 2011 asD7330-111.DOI:10.1520/D7330-15.2For referenced ASTM sta
15、ndards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-
16、2959.United States1 involved shall be compared using a statistical test for unpaireddata,a probability level chosen prior to the testing series.If abias is found either its cause must be found and corrected,orfuture test results for that material must be adjusted inconsideration of the known bias.6.Apparatus6.1 CRI reference Scales A series of imaged standardscontaining a progressive amount of surface appearance changeranging from 5.0(no change)to 1.0(severe change).6.2 Illumination system for a