1、Designation:D647612(Reapproved 2021)Standard Test Method forDetermining Dynamic Air Permeability of Inflatable RestraintFabrics1This standard is issued under the fixed designation D6476;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision
2、,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the procedures used to deter-mine under dynamic airflow conditions the high pressurepe
3、rmeability of permeable,uncoated fabrics typically used forinflatable restraints.For the determination of air permeabilityof inflatable restraint fabrics under low pressure conditions atsteady-state air flow,refer to Test Method D737.1.2 Procedures and apparatus other than those stated in thistest m
4、ethod may be used by agreement of purchaser andsupplier with the specific deviations from the standard ac-knowledged in the report.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address
5、all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in a
6、ccor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM
7、 Standards:2D123 Terminology Relating to TextilesD737 Test Method for Air Permeability of Textile FabricsD1776/D1776M Practice for Conditioning and Testing Tex-tilesD2904 Practice for Interlaboratory Testing of a Textile TestMethod that Produces Normally Distributed Data(With-drawn 2008)3D6799 Termi
8、nology Relating to Inflatable RestraintsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 For all terminology relating to D13.20,Inflatablerestraints,refer to Terminology D6799.3.1.1 The following terms are relevant to this standard:aver
9、age dynamic air permeability(ADAP),dynamic air per-meability(DAP),cushion,exponent of dynamic air permeabil-ity(EXP),inflatable restraint,inflator,module,standard atmo-sphere for testing textiles3.2 For all other terms related to textiles,see TerminologyD123.4.Summary of Test Method4.1 A volume of d
10、esiccated compressed air at knownvolume and pressure passes through a fabric specimen into thestandard atmosphere for testing textiles.During the portion ofthe test cycle which simulates airbag inflation,the pressuredifferential pressure across the specimen rises to a valuecorresponding to a peak in
11、flation pressure.During the portionof the test cycle which simulates airbag deflation,the pressuredifferential drops to 0 kPa as the air passes through thespecimen.The time to reach the maximum pressure and thesubsequent time for the pressure to decrease correspond tosimilar times in an airbag deplo
12、yment.4.2 Software algorithms integral to the apparatus smoothout the pressure data and determine the values for ADAP andEXP.5.Significance and Use5.1 For matters relating to lot acceptance of commercialshipments and conformity to specification or other standard,refer to Section 13 of this test meth
13、od.1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.20 on Inflatable Restraints.Current edition approved July 1,2021.Published July 2021.Originally approvedin 2000.Last previous edition approved in 2017 as D647612(2017)1
14、.DOI:10.1520/D6476-12R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this histor
15、ical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on
16、Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.2 This test method is useful in the selection and designvalidation of permeable,uncoatable fabrics used in inflatablerestraint cushions.The dynamic conditions and higher pressuredifferentials of this test method may better simulate theinflation and deflation cycle of an airbag module duringdeployment than do the steady-state condi