1、Designation:D775419Standard Test Method forDetermination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional GasChromatography1This standard is issued under the fixed designation D7754;the number immediately following the designation indicates the year oforiginal adoptio
2、n or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of traceoxygenates in automotive spark-
3、ignition engine fuel.Themethod used is a multidimensional gas chromatographicmethod using 1,2-dimethoxy ethane as the internal standard.The oxygenates that are analyzed are:methyl-tertiary butylether(MTBE),ethyl-tertiary butyl ether(ETBE),diisopropylether(DIPE),methanol,tertiary-amyl methyl ether(TA
4、ME),n-propanol,i-propanol,n-butanol,i-butanol,tert-butyl alcohol,sec-butyl alcohol,and tert-pentanol.Ethanol is usually notmeasured as a trace oxygenate since ethanol can be used as themain oxygenate compound in finished automotive spark-ignition fuels such as reformulated automotive spark-ignitionf
5、uels.The concentration range of the oxygenates covered in theILS study was from 10 mg kg to 2000 mg kg.In addition thismethod is also suitable for the measurement of the C5 isomericalcohols(2-methyl-1-butanol,2-methyl-2-butanol)presentfrom the fermentation of ethanol.1.2 The ethanol blending concent
6、ration for which this testmethod applies ranges from 1%to 15%by volume.Higherconcentrations of ethanol coelute with methanol in the analyti-cal column.Lower levels of ethanol,similar to the otheroxygenate,can be calibrated and analyzed also.If higherethanol concentrations are expected,the window cut
7、ting tech-nique can be used to avoid ethanol from entering the analyticalcolumn and interfere with the determination of the otheroxygenates of interest.Refer to Appendix X1 for details.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thiss
8、tandard.1.3.1 Alternative units,in common usage,are also providedto increase clarity and aid the users of this test method.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-pr
9、iate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopm
10、ent of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4307 Practice for Preparation of Liquid Blends fo
11、r Use asAnalytical StandardsD4815 Test Method for Determination of MTBE,ETBE,TAME,DIPE,tertiary-Amyl Alcohol and C1to C4Alco-hols in Gasoline by Gas ChromatographyD6304 Test Method for Determination of Water in Petro-leum Products,Lubricating Oils,and Additives by Cou-lometric Karl Fischer Titration
12、3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 electronic pressure control,nelectronic pneumaticcontrol of carrier gas flows.Can be flow or pressure pro-grammed to speed up elution of components.3.1.2 flame ionization detector(FID),ndetector used toanalyze the components eluti
13、ng from the column.3.1.3 fluidic switch,ndevice that reverses the directionalflow in a union T altering the pressure at the midpoint.In itssimplest design it is also known as a Dean Switch.3.1.4 inlet,ncapillary split/splitless inlet system operatedin the split mode is recommended.Operate the inlet
14、within itslinear range.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.04.0L on Gas Chromatography Methods.Current edition approved Nov.1,2019.Published December 2019.Originallyappr
15、oved in 2011.Last previous edition approved in 2016 as D7754 16.DOI:10.1520/D7754-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page
16、onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Comm