1、Designation:D793315Standard Test Method forEngine Coolant Stagnation in Flux-Brazed Aluminum HeatExchangers1This standard is issued under the fixed designation D7933;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last re
2、vision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a laboratory screening proce-dure for evaluating engine coolant compatibility and corrosionprotection afte
3、r aging two weeks at 90C in an aluminum heatexchanger brazed using flux.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It
4、 is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1176 Practice for Sampling and Preparing Aqueous Solu-tions of Engine Coolants o
5、rAntirusts for Testing PurposesD1193 Specification for Reagent WaterD4340 Test Method for Corrosion of Cast Aluminum Alloysin Engine Coolants Under Heat-Rejecting ConditionsE230/E230M Specification and Temperature-ElectromotiveForce(emf)Tables for Standardized Thermocouples3.Summary of Test Method3.
6、1 An aluminum heat exchanger that was brazed using fluxvia any application method or as part of the material claddingis filled with engine coolant,plugged,and placed in an oven fortwo weeks(336 h)at 90C.Engine coolant compatibility isassessed based on changes in coolant physical and composi-tional p
7、roperties,and engine coolant aluminum corrosionprotection is based on performance in the Test Method D4340test.4.Significance and Use4.1 Automobile and truck radiators and heater cores are nowpredominantly made with aluminum alloys using variousmanufacturing processes including brazing with a flux(S
8、eeAppendix X1 for additional information).The presence ofresidual internal brazing flux in heat exchangers along with thehigh ratio of internal aluminum surface area to coolant volumemay affect certain physical and chemical properties and corro-sion protection of the coolant.This test method provide
9、s ascreening test to assess engine coolant physical and chemicalproperties and corrosion protection after aging it in a heatexchanger brazed with flux at elevated temperature understagnant conditions.This method cannot stand alone as evi-dence of satisfactory coolant performance in flux-brazed alu-m
10、inum heat exchangers.The actual service of an enginecoolant formulation can be determined only by more compre-hensive bench,dynamometer,and field tests.5.Apparatus5.1 Aluminum Heat Exchanger Brazed with FluxThe heatexchanger may be a radiator,heater core,or other,liquidcooled heat exchanger.NOTE1The
11、 aluminum brazed heat exchangers used in this testmethod may be commercially produced or experimentally prepared by theheat exchanger supplier.The aluminum grade,alloying,flux loadingduring brazing,and residual flux remaining in the heat exchanger afterbrazing may vary from part to part.The heat exc
12、hanger type,manufacturer,size,and other design parameters are decided by mutualagreement of the parties involved.5.2 Coolant Hoses,Clamps,Hose Adapters,and Caps orPlugsRubber engine coolant hoses(approximately 15 cmlength)of appropriate diameter shall be fitted onto heatexchanger inlet/outlets to al
13、low for coolant expansion.EPDMis one type hose material suitable for the test.Metal clamps,hose adapters,and threaded caps or plugs(stainless steel,orsteel)shall be used to seal the heat exchanger during the1This test method is under the jurisdiction of ASTM Committee D15 on EngineCoolants and Relat
14、ed Fluids and is the direct responsibility of SubcommitteeD15.21 on Extended Life Coolants.Current edition approved May 1,2015.Published May 2015.DOI:10.1520/D7933-152For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book
15、of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 stagnation test.All materials used in the preparation andplumbing of the test specimen sha
16、ll not be galvanic to thealuminum heat exchanger.5.3 Temperature-Measuring Instrument(Thermocouple)An ASTM partial immersion temperature-measuring instru-ment having a range from-20 to 150C and conforming to therequirements for thermocouple as summarized in SpecificationE230/E230M.6.Reagents and Materials6.1 Reagent Grade WaterSpecification D1193 Grade areavailable.7.Test Solution7.1 Engine Coolant Test FluidThe engine coolant testfluid shall be a 50 vol%engine coolant prepared usingSpecificatio