1、Designation:D7747/D7747M11(Reapproved 2018)Standard Test Method forDetermining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the StripTensile Method1This standard is issued under the fixed designation D7747/D7747M;the number immediately following the designat
2、ion indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes destructive qu
3、ality controltests used to determine the integrity of thermo-fusion seamsmade with reinforced geomembranes.Test procedures aredescribed for seam tests for peel and shear properties usingstrip specimens.1.2 The types of thermal field and factory seaming tech-niques used to construct geomembrane seams
4、 include thefollowing:1.2.1 Hot AirThis technique introduces high-temperatureair between two geomembrane surfaces to facilitate melting.Pressure is applied to the top or bottom geomembrane,forcingtogether the two surfaces to form a continuous bond.1.2.2 Hot WedgeThis technique melts the two geomem-b
5、rane surfaces to be seamed by running a hot metal wedgebetween them.Pressure is applied to the top and bottomgeomembrane to form a continuous bond.Some seams of thiskind are made with dual tracks separated by a non-bonded gap.These seams are sometimes referred to as dual hot wedgeseams or double-tra
6、ck seams.1.2.3 ExtrusionThis technique encompasses extrudingmolten resin between two geomembranes or at the edge of twooverlapped geomembranes to effect a continuous bond.1.2.4 Radio Frequency(RF)or DielectricHigh-frequencydielectric equipment is used to generate heat and pressure toform an overlap
7、seam in factory fabrication.1.2.5 ImpulseClamping bars heated by wires or a ribbonmelts the sheets clamped between them.Acooling period whilestill clamped allows the polymer to solidify before beingreleased.1.3 The types of materials covered by this test methodinclude,but are not limited to,reinforc
8、ed geomembranes madefrom the following polymers:1.3.1 Very low-density polyethylene(VLDPE).1.3.2 Linear low-density polyethylene(LLDPE).1.3.3 Flexible polypropylene(fPP).1.3.4 Polyvinyl chloride(PVC).1.3.5 Chlorosulfonated polyethylene(CSPE).1.3.6 Ethylene interpolymer alloy(EIA).1.4 UnitsThe values
9、 stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in noncon-formance with the standard.1
10、.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 T
11、his international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade
12、(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D76/D76M Specification for Tensile Testing Machines forTextilesD4439 Terminology for GeosyntheticsD7003/D7003M Test Method for Strip Tensile Properties ofReinforced GeomembranesD7004/D7004M Test Method for Grab Tensile Properties ofReinforced
13、GeomembranesD7749 Test Method for Determining Integrity of SeamsProduced Using Thermo-Fusion Methods for ReinforcedGeomembranes by the Grab Method1This test method is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.10 on Geomem-branes
14、.Current edition approved Feb.1,2018.Published February 2018.Originallyapproved in 2011.Last previous edition approved in 2013 as D7747/D7747M 111.DOI:10.1520/D7747_D7747M-11R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For
15、Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally rec
16、ognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.Terminology3.1 DefinitionsRefer to Terminology D4439 for defini-tions of terms applying to this test method.4.Significance and Use4.1 The use of reinforced geomembranes as barrier materi-als has created a need for a standard test method to evaluate thequality of