1、Designation:D808218Standard Specification forElemental Impurity Limits in Erosion Control Products usedfor Land Application1This standard is issued under the fixed designation D8082;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard provides a specification for elementalimpurity limits in erosion control products used for landappli
3、cation.Erosion control products may include but are notlimited to:hydraulically-applied erosion control products,rolled erosion control products,sediment retention devices,gabions and mattresses,and articulated concrete block revet-ments.1.2 UnitsThe values stated in SI units are to be regardedas st
4、andard.No other units of measurement are included in thisstandard.1.3 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026,unless superseded by this specification.1.4 This standard does not purport to address all of thesaf
5、ety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance wi
6、th internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D
7、653 Terminology Relating to Soil,Rock,and ContainedFluidsD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD3987 Practice for Shake Extraction of Solid Waste withWaterD6026 Practice for Using Signifi
8、cant Digits in GeotechnicalData2.2 Other Standards:340 CFR 503.13 Pollutant LimitsEPA Method 1312 Mass Transfer Rates of Constituents inMonolithic or Compacted Granular Materials Using aSemi-Dynamic Tank Leaching ProcedureEPA Method 6010D Inductively Coupled PlasmaOpticalEmission SpectrometryEPA Met
9、hod 7000B Flame Atomic Absorption Spectropho-tometryEPA Method 6020A Inductively Coupled PlasmaMassSpectrometry Lethal Dose 50(LD50)or Effective Concen-tration 50(EC50)Method3.Terminology3.1 Definitions:3.1.1 For definitions of common technical terms used in thisstandard,refer to Terminology D653.3.
10、2 Acronyms:3.2.1 ppm,nparts per million4.Specification Requirements4.1 Elemental impurity limits in erosion control productsused for land application shall not exceed the concentrationvalues for the elemental impurities listed in Table 1.5.Sampling5.1 Follow sampling procedures given in ASTM Practic
11、eD3987 to obtain the samples and test specimens.Productswhich are impermeable such as plastics and metal productsneed not to be reduced below 100-gram sample sizes.6.Test Methods6.1 Use Practice D3987 or method EPA 1312 with extrac-tion fluid#3 to extract the leachate.1This test method is under the
12、jurisdiction ofASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.25 on Erosion andSediment Control Technology.Current edition approved Aug.1,2018.Published August 2018.DOI:10.1520/D8082-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcont
13、act ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3For referenced Code of Federal Regulations and Environmental ProtectionAgency standards,visit their respective websites,www.gpo.gov/fdsys
14、andwww.epa.gov/hw.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelop
15、ment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.2 After extraction,use EPA Methods 6020A,6010,or7000B with detection limits below the lowest value for eachelemental impurity in Table 1 to determine the im
16、purityanalysis of the erosion control product.6.3 Compare the values obtained from the impurity analysisto those values in Table 1 to determine if the erosion controlproducts meets the performance requirements.NOTE1The quality of the result produced by this standard isdependent on the competence of the personnel performing it,and thesuitability of the equipment and facilities used.Agencies that meet thecriteria of Practice D3740 are generally considered capable of competentand objective testing/