ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:63.75KB ,
资源ID:173804      下载积分:8 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/173804.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_7888_-_13.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_7888_-_13.pdf

1、Designation:D788813Standard Practice forEvaluating Adhesive and the Effects of Plasticizer FoundWithin Polyvinyl Chloride-Backed Floor Coverings1This standard is issued under the fixed designation D7888;the number immediately following the designation indicates the year oforiginal adoption or,in the

2、 case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard will provide a qualitative means to deter-mine the potential effects of plastic

3、izers contained withinpolyvinyl chloride(PVC)floor covering materials on a specificadhesive.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered sta

4、ndard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced

5、 Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD907 Terminology of AdhesivesF141 Terminology Relating to Resilient Floor Coverings3.Terminology3.1 Definitions:3.1.1 plasticizer,nadditives that increase the plasticity orfluidity of a material;a chemical added especially to rubbers

6、and resins to impart flexibility,workability,or elasticity.3.1.2 polyvinyl chloride(PVC),na thermoplastic polymerused in many floor covering materials.4.Significance and Use4.1 Plasticizer migration is detrimental to many adhesives,including hot melts,which could be possibly used in conjunc-tion wit

7、h PVC backed flooring materials,whether resilient ortextile,broadloom,tile or plank.This practice can be used as anindicator to determine if plasticizers in the flooring material arecompatible with proposed installation adhesive(s).5.Apparatus5.1 Circulating Air Oven,capable of maintaining 140 6 3F(

8、60 6 2C).5.2 Test Adhesive.5.3 Test Floor Covering.5.4 Floor Covering Seam-roller,(approximately 2 lb(1 kg).5.5 U Notched Trowel,132in.by116in.by132in.(0.079 cmby 0.16 cm by 0.079 cm),or alternate means of application.5.6 Four Pieces of Aluminum Foil,approximately 26 in.by10 in.(66 cm by 25 cm).6.Pr

9、ocedure6.1 Cut four 6 in.by 6 in.(15 cm by 15 cm)pieces of thePVC backed flooring test material.Material composition canbe textile or resilient.6.2 Using the recommended application method as in-structed by the floor covering or adhesive manufacturer(trowel,roller,or spray)apply the adhesive to the

10、backing oftwo of the 6 in.by 6 in.(15 cm by 15 cm)pieces of floorcovering.If no application method is specified use a132in.by116in.by132in.(0.079 cm by 0.16 cm by 0.079 cm)U notchedflooring trowel.6.3 Allow the adhesive on the test specimens to dry at roomconditions maintained at 73 6 3F(23 6 2C)and

11、 50 6 5%relative humidity for not less than 3 h before testing.6.4 Place each of the uncoated 6 in.by 6 in.(15 cm by 15cm)pieces back-to-back to the adhesive coated specimensforming two test assemblies.6.5 Press the test assembly together rolling completelyusing a floor covering seam-roller or simil

12、ar type method toensure firm and even contact between the coated and uncoatedsurfaces.6.6 Completely wrap the test assemblies in aluminum foil sothat each assembly is fully sealed.It is recommended toenvelope and tightly seal the test specimens with two layers ofaluminum foil.1This practice is under

13、 the jurisdiction of ASTM Committee D14 on Adhesivesand is the direct responsibility of Subcommittee D14.10 on Working Properties.Current edition approved Oct.15,2013.Published November 2013.DOI:10.1520/D7888-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Custom

14、er Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.7 Place one of the test assemblies in the

15、oven at 140 63F(60 6 2C)for 15 days 6 3 h.The second assembly shallbe maintained in controlled environment of 73 6 3F(23 62C)and 50 6 5%relative humidity for an equal time period.6.8 After 15 days remove the test assembly from the ovenand allow to cool at room temperature for a period of not lesstha

16、n 30 6 5 min.6.9 Remove the test assembly form the aluminum foil,andthen separate the two assemblies comparing the one taken fromthe oven,with the one allowed to remain under room condi-tions for signs of apparent plasticizer migration or differencesin adhesion.Examine the adhesive line for any gumminess oroily feel to the adhesive.6.10 Record and report all observations.7.Report7.1 Date,time and duration of test7.2 Compare and evaluate the two test specimens and reportthe difference,in appearan

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2