1、Designation:D 6180 05Standard Test Method forStability of Insulating Oils of Petroleum Origin UnderElectrical Discharge1This standard is issued under the fixed designation D 6180;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the ye
2、ar of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a laboratory technique thatmeasures the stability of new,used,or reclaimed insulatingoils,si
3、milar to those described in Specification D 3487 in thepresence of a controlled electric discharge.When subjected tothis type of discharge,insulating oils absorb energy andproduce gases as well as ionized molecules(charge carriers).The quantity of these decay products can be measured and canprovide
4、an indication of the stability of oils under the condi-tions of this test.1.2 The gases are retained in the discharge cell and theirpressure measured.The charge carriers remain in the testspecimen.The change in the dissipation factor before and afterthe discharge is determined.1.3 The values stated
5、in SI units are to be regarded as thestandard.The values stated in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and heal
6、th practices and determine the applica-bility of regulatory limitations prior to use.Specific cautionarystatements are given in 5.3 and 7.1.2.Referenced Documents2.1 ASTM Standards:2D 923 Practice for Sampling Electrical Insulating LiquidsD 924 Test Method for Dissipation Factor(or Power Factor)and
7、Relative Permittivity(Dielectric Constant)of Electri-cal Insulating LiquidsD 3487 Specification for Mineral Insulating Oil Used inElectrical Apparatus2.2IEEE Standard:41995 IEEE Standard Techniques for High-Voltage Test-ing33.Summary of Test Method3.1 A test specimen is introduced into a discharge c
8、ell anddegassed under vacuum at room temperature.An ac potentialof 10 kV is applied between a high voltage electrode and agrounded salt water electrode for 300 min.The gradual rise ofthe pressure inside the discharge cell is measured on anelectronic vacuum meter as a function of time.The dissipation
9、factor of the oil at 100C is determined before and after thestability test.4.Significance and Use4.1 During this test,insulating oil in an evacuated cell issubjected to a high voltage discharge between two electrodes.The discharge generates free electrons.These electrons collidewith the oil molecule
10、s causing many of them to becomeelectronically excited.Some of these molecules lose thisenergy as a quanta of light emitting fluorescent radiation.Someof the other excited molecules decompose into gases,ionizedmolecules and free radicals.These changes can provide anindication of the stability of oil
11、s under the conditions of thistest method.The measures of these changes are the increase ofthe pressure in the test cell and the increase in the dissipationfactor of the test specimen.4.2 During the test,the gas content increases in the cell andthe concentration of charge carriers increases in the o
12、il.5.Apparatus5.1 Discharge Cell,4shown in Fig.1,includes an electronicvacuum meter.The cell must be made of quartz,be of sphericalshape,and have a 500 mL capacity.The electrode is sealed in1This test method is under the jurisdiction of ASTM Committee D27 onElectrical Insulating Liquids and Gases an
13、d is the direct responsibility of Subcom-mittee D27.05 on Electrical Test.Current edition approved Oct.1,2005.Published October 2005.Originallyapproved in 1997.Last previous edition approved in 2004 as D 6180-98(2004).2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM
14、Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from the Institute of Electrical and Electronic Engineers,Inc.,P.O.Box 1331,Piscataway,NJ 08855.4The sole source of supply of the dischar
15、ge cell known to the committee at thistime is Insoil Canada Ltd.,231 Hampshire Place,N.W.,Calgary,AB Canada T3A4Y7.If you are aware of alternative suppliers,please provide this information toASTM International Headquarters.Your comments will receive careful consider-ation at a meeting of the respons
16、ible technical committee1,which you may attend.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.the cell as shown in Fig.1.The free electrons are generated bya cylindrical copper electrode 15 mm(0.6 in.)in diameter and10 mm(0.4in.)long,which is placed in the center of thedischarge cell.5.2 Glass Dish,approximately 150 mm(6 in.)in diameterand 100 mm(4 in.)deep for holding a salt-water groundelectrode.5.3 Test Chamber,with safety interlo