ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:67.34KB ,
资源ID:174175      下载积分:8 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/174175.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_7734_-_D_7734M_-_13_2020.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_7734_-_D_7734M_-_13_2020.pdf

1、Designation:D7734/D7734M13(Reapproved 2020)Standard Test Method forDetermination of Open Time of Oxidative Printing Inks andOverprint Varnishes by a Manual Method1This standard is issued under the fixed designation D7734/D7734M;the number immediately following the designation indicates theyear of or

2、iginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a manual procedure for deter-mining the stay

3、 open time of oxidative drying printing inks andoverprint varnishes by a finger transfer method.Open isdefined as a wet ink/varnish film.1.2 The amount of time required to reach the endpoint isrecorded in hours.1.3 Typical inks and overprint varnishes that dry by oxida-tion are oil based sheetfed of

4、fset,letterpress,and screen inks.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system are not necessarily exact equivalents;therefore,toensure conformance with the standard,each system shall beused independently of the

5、other,and values from the twosystems shall not be combined.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine th

6、e applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issue

7、d by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Summary of Test Method2.1 Inks and overprint varnishes are applied to a glasssurface using a wet film applicator and checked at timeintervals using a finger transfer method to determine the timethat the ink/varnish are no l

8、onger open.3.Significance and Use3.1 When formulating printing inks and overprint varnishesthat dry primarily by oxidation it is important to know the stayopen time so that premature drying does not occur on theprinting press rollers and other components.3.2 The applied ink or OPV film used for test

9、ing is thickerthan the film printed on the substrate and nominally representsthe film on the printing press rollers.4.Apparatus4.1 Clean Dry Uniform Glass Plate,approximately 20 cmwide by 25 cm long 8 by 10 in.4.2 Machined Wet Film Applicator,with the appropriateclearance gap typically in a range of

10、 12 to 75 m 0.5 to 3.0mils which provides a wet film thickness of 6 to 35 m 0.25to 1.5 mils.4.3 Stop Watch or Timer,with alarm.4.4 Ink Knife(s).5.Reagents and Materials5.1 Clean up Solvent.5.2 Clean up Rags.6.Preparation of Apparatus6.1 Ensure that the wet film applicator is clean and free ofnicks o

11、r other defects.6.2 Ensure that the glass plate surface is clean,uniformlylevel and free of any dust,solvent or residue.7.Conditioning7.1 Nominal laboratory standard conditions of 23 6 2C 736 3.5F temperature and 50 6 5%relative humidity level arerecommended for this test.Deviations from these condi

12、tionswill affect results.7.2 Glass plate should be located free from drafts orexcessive air movement.8.Procedure8.1 Select the appropriate clearance gap that will provide awet film thickness in the range of 12 to 75 m 0.5 to 3.0 milsor as agreed upon by seller and purchaser.8.2 Place the applicator

13、on the glass and apply approxi-mately an 8 cm 3 in.wide sample of the ink or overprint1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.56 on Printing Inks.Current edition appr

14、oved June 1,2020.Published July 2020.Originally approvedin 2013.Last previous edition approved in 2013 as D7734/D7734M 13.DOI:10.1520/D7734_D7734M-13R20.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was develop

15、ed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.varnish in front of gap i

16、n the pulling direction.The amount ofink needs to be sufficient to produce a wet film about 15 to 20cm 6 to 8 in.long.8.3 Grasp the sides of the applicator with the fingers anddraw down at a uniform speed(approximately 25 mm/s)withsufficient pressure to maintain direct surface contact of theapplicator with the glass plate.8.4 Clean applicator immediately with cleaning solvent andrags.8.5 Set the timer for one hour.NOTE1One hour time intervals are the maximum suggested test cycletime for most pri

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2