1、Designation:D773911(Reapproved 2020)An American National StandardStandard Practice forThermal Oxidative Stability Measurement via Quartz CrystalMicrobalance1This standard is issued under the fixed designation D7739;the number immediately following the designation indicates the year oforiginal adopti
2、on or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This laboratory practice covers the quantitative determi-nation of surface deposi
3、ts produced during the thermal oxida-tion of gas turbine fuels by monitoring the oscillation fre-quency of a quartz crystal during thermal exposure.In thispractice,“thermal oxidative stability”refers to the tendency ofa fuel to resist surface deposit formation during heating.1.2 The values stated in
4、 SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and
5、environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International St
6、andards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Summary of Practice2.1 A quartz crystal,fitted with gold electrodes,is fullyimmersed in test fuel contained within a reactor.An oscillatorcircuit,connected to the crystal,supplies en
7、ergy to excite thequartz crystal and monitors its resonant frequency(nominally5 MHz)over time via a computer interface.The reactor isequipped with a magnetic stir bar,pressure gauge/transducer,oxygen sensor(not recommended for certain test conditions,see 4.11),and thermocouple to monitor and control
8、 testconditions.Prior to testing,the fuel is bubbled with the test gasfor 30 min to equilibrate.After equilibration,the reactor vesselis isolated and raised to test temperature and pressure.Asdeposits accumulate on the crystal surface during the run,thecrystal frequency decreases.The shift in resona
9、nce frequencycan be quantitatively related,in real time,to surface depositaccumulation via a variation of the Sauerbrey equation.23.Significance and Use3.1 The tendency of a jet fuel to resist the formation ofdeposits at elevated temperature is indicative of its oxidativethermal stability.This pract
10、ice provides a technique for thesimultaneous determination of deposit formation and oxygenconsumption during the thermal oxidation of jet fuels and otherhydrocarbon liquids.The practice can be used to evaluate thethermal stability of fuels and to determine the efficacy ofadditives in inhibiting depo
11、sition or slowing oxidation,or both.Atest temperature of 140 C and run length up to 16 h has beenfound to be effective for the relative evaluation of fuels andfuel additives.This practice has also been employed for otherhydrocarbon liquids,such as gasoline and diesel fuels,butadditional safety issue
12、s may need to be addressed by the user.4.Apparatus4.1 All dimensions without tolerance limits are nominalvalues.4.2 ReactorA T316,100 mL stainless steel reactor cylin-der with an internal diameter of 5.23 cm(2.06 in.)and a depthof 4.93 cm(1.94 in.).3,4A T316 stainless steel reactor headwith several
13、openings(for example,gas inlet via dip tube,gasrelease fitted with a dial gauge or pressure transducer,thermocouple,safetyrupturedisk,frequencysignalconnection,sleeve for oxygen concentration probe).A0.952 cm(38in.)hole is drilled in the center of the reactor headto accommodate the frequency signal
14、connectors.This holeshall have a 0.952 cm(38in.)clearance from any adjacentopening.1This practice is under the jurisdiction of ASTM Committee D02 on PetroleumProducts,Liquid Fuels,and Lubricants and is the direct responsibility of Subcom-mittee D02.J0.03 on Combustion and Thermal Properties.Current
15、edition approved Dec.1,2020.Published December 2020.Originallyapproved in 2011.Last previous edition approved in 2016 as D7739 11(2016).DOI:10.1520/D7739-11R20.2Klavetter,E.A.,Martin,S.J.,and Wessendorf,K.O.,“Monitoring Jet FuelThermal Stability Using a Quartz Crystal Microbalance,”Energy&Fuels,Vol
16、3,1993,pp.582-588.3The sole source of supply of the apparatus(Parr Instrument cylinder model#452HC8(100 mL)known to the committee at this time is Parr InstrumentCompany,211 Fifty-Third St.,Moline,IL 61265-1770.4If you are aware of alternative suppliers,please provide this information toASTM International Headquarters.Your comments will receive careful consider-ation at a meeting of the responsible technical committee,1which you may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box