1、Designation:D6037131Standard Test Methods forDry Abrasion Mar Resistance of High Gloss Coatings1This standard is issued under the fixed designation D6037;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num
2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEReference to research report was added editorially to Test Method B in August 2013.1.Scope*1.1 This test method covers procedures for evaluating the
3、relative mar resistance of high gloss coatings.Two testmethods are included.Test Method A uses a device thatcontains a rotating specimen holder and two abrasive wheels.Test Method B uses a device that contains a reciprocatingspecimen holder and a single wheel that has been fitted withabrasive paper.
4、Either method can be used to evaluate the dryabrasion mar resistance of coatings applied to planar,rigidsurfaces.Each test method provides good discrimination be-tween highly mar resistant coatings.NOTE1The mar resistance values obtained by these test methods haveno absolute significance.They should
5、 only be used to derive relativeperformance rankings for test panels that have been prepared from theseries of coatings that are currently being evaluated.If mar resistancevalues are quoted between laboratories,it is essential that a commonstandard be measured and that the values be compared to that
6、 standard.Even then,the values should be used with caution.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespon
7、sibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D523 Test Method for Specular GlossD609 Practice for Preparation of Cold-Rolled Steel Panelsfo
8、r Testing Paint,Varnish,Conversion Coatings,andRelated Coating ProductsD823 Practices for Producing Films of Uniform Thicknessof Paint,Varnish,and Related Products on Test PanelsD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD3924 Specification for Envi
9、ronment for Conditioning andTesting Paint,Varnish,Lacquer,and Related MaterialsD4060 Test Method for Abrasion Resistance of OrganicCoatings by the Taber AbraserD4449 Test Method for Visual Evaluation of Gloss Differ-ences Between Surfaces of Similar AppearanceD7091 Practice for Nondestructive Measur
10、ement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic,Nonconductive Coat-ings Applied to Non-Ferrous MetalsE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of
11、 a Test Method3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 mar resistance,nthe ability of a coating to resistpermanent deformation or fracture,resulting from the applica-tion of a dynamic mechanical force.These test methodsmeasure resistance to visible damage caused by mild
12、abrasion.4.Summary of Test Method4.1 The coatings that are being evaluated are applied atuniform dry film thickness to planar panels of uniform surfacetexture.After drying or curing,or both,the panels are marred.Mar resistance is assessed by measuring the coatings glosswithin the abraded and unabrad
13、ed areas of test panels.Marresistance is directly related to the coatings ability to retaingloss in abraded areas.5.Significance and Use5.1 Coatings,particularly the high gloss coatings used onautomobiles,boats,toys,etc.,are subject to a wide variety ofconditions(for example,wiping,cleaning,and expo
14、sure)thatcan mar their surface.The ability of these coatings to maintaintheir appearance is an important product attribute.These test1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings,Materials,and Applications and are the directresponsibility of Subcom
15、mittee D01.23 on Physical Properties of Applied PaintFilms.Current edition approved June 1,2013.Published August 2013.Originallyapproved in 1996.Last previous edition approved in 2008 as D6037 96(2008).DOI:10.1520/D6037-13E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta
16、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 methods provide a way to estimate the ability of high glosscoatings to resist mar damage.5.2 These test methods do not provide fundamental values.However they are su