1、Designation:D622621Standard Test Method forOpen Cell Content of Rigid Cellular Plastics1This standard is issued under the fixed designation D6226;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in p
2、arentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers cellular plastics,which arecomposed of membranes or walls of polymer separating smallcavities or cells.These cells may be int
3、erconnecting(opencell),non-connecting(closed cell),or any combination of thesetypes.This test method determines numerical values for opencells.It is a porosity determination,measuring the accessiblecellular volume of a material.The remaining volume is thatoccupied by closed cells and cell walls.Sinc
4、e any convenientlysized specimen is typically obtained by some cutting operation,a fraction of the closed cells will be opened by specimenpreparation and will be included as open cells,(see Note 2).1.2 This test method provides good accuracy on predomi-nantly highly open-celled materials.By not acco
5、unting forclosed cells that were opened during specimen preparation,theaccuracy decreases as the closed cell content increases and asthe cell size increases.1.3 The values as stated in SI units are to be regarded as thestandard.The values in parentheses are given for referenceonly.1.4 This standard
6、does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE1This test method
7、and ISO 4590 use the same basic principlesbut are significantly different in experimental detail.NOTE2Two procedures for correcting for cells opened duringspecimen preparation are described in Appendix X1.1.1.5 This international standard was developed in accor-dance with internationally recognized
8、principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to Pl
9、asticsD2842 Test Method for Water Absorption of Rigid CellularPlasticsD3576 Test Method for Cell Size of Rigid Cellular PlasticsE456 Terminology Relating to Quality and StatisticsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 ISO Standard:ISO 4590
10、 Cellular PlasticsDetermination of Volume Per-centage of Open and Closed Cells of Rigid Materials33.Terminology3.1 Definitions:3.1.1 Terms used in this standard are defined in accordancewith Terminology D883,unless otherwise specified.For termsrelating to precision and bias and associated issues,the
11、 termsused in this standard are defined in accordance with Terminol-ogy E456.3.2 Definitions of Terms Specific to This Standard:3.2.1 closed cella cell totally enclosed by its walls andhence not interconnecting with other cells.3.2.2 open cella cell not totally enclosed by its walls andopen to the s
12、urface either directly or by interconnecting withother cells.3.2.3 volume of closed cells and cell wallsinaccessibleinternal volume,consisting of an aggregate of solid polymervolume(cell walls,struts),filler volume,when applicable(solid particles or fibers),the volume of individual closed cells,and
13、the volume of small cell groups interconnected by rupturedcell walls but otherwise inaccessible.3.2.4 uncorrected volume of open cellsthe aggregate mea-surement of both the internal porous volume of the materialand the various irregular volumes accessible at the cut-cellsurface of the test specimen.
14、1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.22 on Cellular Materials-Plastics and Elastomers.Current edition approved Feb.15,2021.Published February 2021.Originallyapproved in 1998.Last previous edition approved in
15、 2015 as D6226-15.DOI:10.1520/D6226-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Na
16、tional Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World