1、Designation:D6024/D6024M16Standard Test Method forBall Drop on Controlled Low Strength Material(CLSM)toDetermine Suitability for Load Application1This standard is issued under the fixed designation D6024/D6024M;the number immediately following the designation indicates theyear of original adoption o
2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method explains the determination of theability of Controlled Low Strength
3、 Material(CLSM)to with-stand loading by repeatedly dropping a metal weight onto thein-place material.1.2 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026.1.2.1 The procedures used to specify how data are collected/reco
4、rded and calculated in the standard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that generally should be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations
5、 for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to becommensurate with these considerations.It is beyond the scopeof these test methods to consider significant digits used inanalysis methods for engineering data.1.3 UnitsThe values stated
6、in either SI units or inch-pound units presented in brackets are to be regarded separatelyas standard.The values stated in each system shall be usedindependently of the other.Combining values from the twosystems may result in non-conformance with the standard.1.4 CLSM is also known as flowable fill,
7、controlled densityfill,soil-cement slurry,soil-cement grout,unshrinkable fill,“K-Krete,”and other similar names.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety
8、 and health practices and determine the applica-bility of regulatory limitations prior to use.(WarningFreshhydraulic cementitious mixtures are caustic and may causechemical burns to skin and tissue upon prolonged exposure.2)2.Referenced Documents2.1 ASTM Standards:3C125 Terminology Relating to Concr
9、ete and Concrete Ag-gregatesD653 Terminology Relating to Soil,Rock,and ContainedFluidsD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD4832 Test Method for Preparation and Testing of Con-trolled Lo
10、w Strength Material(CLSM)Test CylindersD6023 Test Method for Density(Unit Weight),Yield,Ce-ment Content,and Air Content(Gravimetric)of Con-trolled Low-Strength Material(CLSM)D6026 Practice for Using Significant Digits in GeotechnicalDataD6103 Test Method for Flow Consistency of ControlledLow Strengt
11、h Material(CLSM)(Withdrawn 2013)43.Terminology3.1 Definitions:3.1.1 For definitions of common technical terms in this testmethod,refer to Terminology standards C125 and D653.3.1.2 Controlled Low Strength Material(CLSM),na mix-ture of soil,aggregates(sand,gravel,or both),cementitiousmaterials,water,a
12、nd sometimes admixtures,that hardens intoa material with a higher strength than the soil,but less than8400 kPa 1200 psi.3.1.2.1 DiscussionUsed as a replacement for compactedbackfill,CLSM can be placed as a slurry,a mortar,or acompacted material and typically has strengths of 350 to 700kPa 50 to 100
13、psi for most applications.1This test method is under the jurisdiction ofASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.15 on Stabilization WithAdmixtures.Current edition approved Dec.1,2016.Published January 2017.Originallyapproved in 1995.Last previous editi
14、on approved in 2015 as D6024 07.DOI:10.1520/D6024_D6024M-16.2Section on Safety Precautions,Manual of Aggregate and Concrete Testing,Annual Book of ASTM Standards,Vol.04.02.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual
15、 Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor
16、Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.Summary of Test Method4.1 A half spherical weight is dropped five times from aspecific height onto the surface of in-pl