1、Designation:D590920Standard Test Method forDrying Time of Oxidative-Drying Printing Inks by SqualeneResistance1This standard is issued under the fixed designation D5909;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、 revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the procedure for determiningthe drying time of oxidative-drying printing inks(also referredto as“sheet
3、fed inks”)by squalene resistance of printed inkfilms.1.2 This test method is applicable to all paste inks that dryprimarily by oxidation regardless of the substrate on whichthey are printed.With appropriate changes in the test fluid,itmay also be used with paste inks that dry by other mechanisms,suc
4、h as heatset or ultraviolet light.1.3 This test method utilizes a modified rub tester and isintended to serve as a“referee”procedure when laboratories,using less rigorous test procedures(see Appendix X1),cannotagree on their results.1.4 The values stated in SI units are to be regarded as thestandard
5、.The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the
6、applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued
7、by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4332 Practice for Conditioning Containers,Packages,orPackaging Components for TestingD5264 Practice forAbrasion Resistance of Printed Materialsby the Sutherland Rub Tester3.Terminology
8、3.1 Definitions of Terms Specific to This Standard:3.1.1 blanket,na composite structure,normally a rubber-like layer supported by one or more fabric or foam layers,orboth.3.1.2 squalene oil,nan organic liquid(C30H50unsaturatedaliphatic hydrocarbon)that imitates the action of skin oil.3.1.3 Discussio
9、nSqualene dissolves vehicle componentsin a typical oxidative-drying ink system but not when fullypolymerized.4.Summary of Test Method4.1 The test print is affixed to the base of the rub tester.Theremovable one-half pound weight of the instrument is fittedwith a piece of rubber blanket and covered wi
10、th an absorbenttowel to which a small amount of squalene oil has been added.The weighted,oil-impregnated towel is allowed to rub backand forth over the test print for a prescribed number of cycles.4.2 The receptor towel is examined for evidence of inktransfer from the print.Results may be related qu
11、alitatively toan agreed upon standard,or,the intensity of the stain can bemeasured quantitatively with a colorimeter,spectrophotometer,or other reflectance type device.5.Significance and Use5.1 Inadequate setting or drying of sheetfed inks,or both,can cause blocking of stacked prints with subsequent
12、 loss ofproduct.“Setting”of an ink refers to the rapid rise in viscosityof the printed ink film,sometimes accompanied by surfacedrying,that prevents transference of the undried ink film toadjacent surfaces under light pressure.“Setting”is a propertyof the ink-substrate combination.Inadequate drying
13、may bedue to several factors,but the primary causes are:(1)omissionof metallic driers from the ink,improper ink formulation(2)unusual ink-substrate interactions,and(3)use of a fountainsolution that is too acidic.If the test prints are made on a1This test method is under the jurisdiction of ASTM Comm
14、ittee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.56 on Printing Inks.Current edition approved June 1,2020.Published June 2020.Originallyapproved in 1996.Last previous edition approved in 2011 as D5909 96a(2011)which was withdrawn J
15、anuary 2020 and reinstated in June 2020.DOI:10.1520/D5909-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyr
16、ight ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.standard laboratory proof press,where there is no applicationof fountain solution,t