1、Designation:D604118An American National StandardStandard Specification forContact-Molded“Fiberglass”(Glass-Fiber-ReinforcedThermosetting Resin)Corrosion Resistant Pipe andFittings1This standard is issued under the fixed designation D6041;the number immediately following the designation indicates the
2、 year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers pipe and fittings fabricated by
3、contact molding,for pressures to 150 psi and made of acommercial-grade polyester resin.Included are requirementsfor materials,properties,design,construction,dimensions,tolerances,workmanship,and appearance.1.2 This specification does not cover resins other thanpolyester,reinforcing materials other t
4、han glass fibers orfabrication methods other than contact molding.NOTE1For the purposes of this specification,the term polyester resinwill include both polyester and vinylester resins.1.3 This specification does not cover the design of pipe andfittings intended for use with liquids heated above thei
5、r flashpoints.1.4 The values stated in inch-pound units are to be regardedas the standard.The SI units given in parentheses are providedfor information purposes only.1.5 The following precautionary caveat pertains only toSection 10,the test methods portion,of this specification:Thisstandard does not
6、 purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.NOTE2There is no known ISO equiva
7、lent to this standard.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization
8、 TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C581 Practice for Determining Chemical Resistance ofThermosetting Resins Used in Glass-Fiber-ReinforcedStructures Intended for Liquid ServiceC582 Specification for Contact-Molded Reinforced Thermo-setting Plastic(RTP
9、)Laminates for Corrosion-ResistantEquipmentD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD883 Terminology Relating to PlasticsD1599 Test Method f
10、or Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2583 Test Method for Indentation Hardness of Rigid Plas-tics by Means of a Barcol ImpressorD2584 Test Method for Ignition Loss of Cured ReinforcedResinsD3567
11、Practice for Determining Dimensions of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)Pipe andFittingsD3681 Test Method for Chemical Resistance of“Fiberglass”(GlassFiberReinforced Thermosetting-Resin)Pipe in aDeflected ConditionD5421 Specification for Contact Molded“Fiberglass”(Glass-Fiber-R
12、einforced Thermosetting Resin)FlangesF412 Terminology Relating to Plastic Piping Systems2.2 ANSI Standards:B16.1 Cast Iron Pipe Flanges and Flanged Fittings3B16.5 Pipe Flanges and Flanged Fittings3B18.22 Type“B”Narrow Washers31This specification is under the jurisdiction of ASTM Committee D20 onPlas
13、tics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved Nov.1,2018.Published November 2018.Originallyapproved in 1996.Last previous edition approved in 2011 as D6041 11.DOI:10.1520/D6041-18.2For referenced ASTM
14、standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New
15、 York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized princ
16、iples on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.3 National Sanitation Foundation Standard:NSF Standard 61 Drinking Water System ComponentsHealth Effects43.Terminology3.1 Definitions:3.1.1 GeneralDefinitions are in accordance with Termi-nology D883 and Terminology F412 and abbreviations are inaccordance with Terminology D1