1、Designation:D632598(Reapproved 2019)Standard Test Method forDetermining Open Assembly Time of Carpet MasticAdhesives1This standard is issued under the fixed designation D6325;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year o
2、f last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes a procedure to measure openassembly time for a troweled carpet adhesive.1.2 This test method p
3、rovides an evaluation of the ability ofan adhesive to effectively wet out the intended carpet backing.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not cons
4、idered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations p
5、rior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization Technical
6、Barriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C679 Test Method for Tack-Free Time of Elastomeric Seal-antsD618 Practice for Conditioning Plastics for TestingD907 Terminology of Adhesives3.Terminology3.1 Definitions:3.1.1 Many of the terms in this test method are defined i
7、nTerminology D907.4.Significance and Use4.1 The ability to have a sufficient open assembly time iscritical when bonding a carpet.An adhesive with too short anopen assembly time will not allow the installer enough time toposition the carpet before the adhesive is dried beyond use.Aproduct with too lo
8、ng an open assembly time will not provideenough dry time for the carpet to bond to the intended substratewithout movement of the carpet.4.2 The test method provides a means of measuring theopen assembly time for an adhesive.Use of such a test methodcan aid both the manufacturer to develop and the us
9、er to selectthe appropriate adhesive for the installation of carpet.4.3 Test Method C679 was used as a model for this testmethod.5.Apparatus5.1 Applicator Trowel18in.(3.2 mm)wide,18in.(3.2mm)deep,116in.(1.6 mm)space V-notch.5.2 One-kg Weight,at least 2 in.(51 mm)in diameter.5.3 Chronometer.6.Materia
10、ls6.1 AdhesiveAny appropriate adhesive used to installcarpet.6.2 PolyethyleneLow density(LDPE)with a 0.006 in.(0.15 mm)thickness.6.3 Glass,12 in.by 12 in.7.Conditioning7.1 Condition the LDPE,glass,and adhesive to be tested 24h prior to testing at 73.4 6 3.6F(23 6 2C)and 50 6 5%relative humidity acco
11、rding to Practice D618.8.Sample Preparation8.1 Cut the LDPE into twenty 2 in.(50.8 mm)by 2 in.(50.8mm)pieces.9.Procedure9.1 Hold the trowel at a 45 angle and spread enoughadhesive to cover the entire glass surface.Start the chronom-eter.1This test method is under the jurisdiction of ASTM Committee D
12、14 onAdhesives and is the direct responsibility of Subcommittee D14.70 on ConstructionAdhesives.Current edition approved March 1,2019.Published March 2019.Originallyapproved in 1998.Last previous edition approved in 2011 as D6325 98(2011).DOI:10.1520/D6325-98R19.2For referenced ASTM standards,visit
13、the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United S
14、tatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to T
15、rade(TBT)Committee.1 9.2 Place an LDPE square on the adhesive taking care not toput unnecessary pressure on it.9.3 Apply the 1 kg weight on the LDPE for 10 s.9.4 Grasp one end of the LDPE square and slowly peelaway(at a 90 degree angle)the LDPE within 5 s.Record thepercentage of the adhesive transfe
16、rred to the LDPE.9.5 Every 5 min after the adhesive was originally troweled,repeat steps 9.2 9.4 using a new LDPE square on a section ofadhesive not previously tested or bonded.9.6 Continue the testing until you have no adhesive transfer.9.7 This is the open assembly time.10.Report10.1 Report the following information:10.1.1 The type of carpet adhesive used.10.1.2 The substrates used.10.1.3 The adhesive open time.Record the%of LDPE areacovered as a function of time in minutes until no furthertra