1、Designation:D549217Standard Test Method forDetermination of Xylene Solubles in Propylene Plastics1This standard is issued under the fixed designation D5492;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method is to be used for determining the 25Cxylene-soluble fraction of polypropylene homopolymers andcopolymers.1.2 This standard
3、 does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE1This test method
4、 is technically equivalent to ISO 16152.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World
5、Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsE456 Terminology Relating to Quality and StatisticsE691 Practice for Conducting an Interlaboratory St
6、udy toDetermine the Precision of a Test MethodE2935 Practice for Conducting Equivalence Testing inLaboratory Applications2.2 ISO Standard:ISO 16152 PlasticsDetermination of Xylene Solubles ofPolypropylene33.Terminology3.1 Definitions:3.1.1 For definitions of plastic terms see Terminology D883and for
7、 abbreviations see Terminology D1600.3.2 Definitions of Terms Specific to This Standard:3.2.1 soluble-fraction(SS)the percentage of the polymermass that does not precipitate out when the polymer solution iscooled from reflux temperature to+25 6 0.5C and held at thattemperature for a specified period
8、 of time.4.Summary of Test Method4.1 A weighed amount of sample is dissolved in xyleneunder reflux conditions.The solution is cooled under con-trolled conditions and maintained at a+25C equilibriumtemperature so that the crystallization of the insoluble fractiontakes place.When the solution is coole
9、d the insoluble portionprecipitates and is isolated by filtration.The xylene is evapo-rated from the filtrate,leaving the soluble fraction in theresidue.The percentage of this fraction in the plastic isdetermined gravimetrically.5.Significance and Use5.1 The results of this test provide a relative m
10、easure of thetotal soluble fraction of polypropylene homopolymers andcopolymers.The soluble fraction approximately correlates tothe amorphous fraction in the polypropylene.Xylene is widelyused for determining the soluble fraction in polypropylene as itis more specific to the atactic fraction than ot
11、her solvents.Theconcentration of a soluble fraction obtained with a specificsolvent has been found to relate closely to the performancecharacteristics of a product in certain applications,for examplefilm and fiber.Data obtained by one solvent and at oneprecipitation time cannot be compared with data
12、 obtained byanother solvent or precipitation time,respectively.6.Interferences6.1 It is possible that materials with solubilities similar tothe soluble fraction,such as additives,can interfere with themeasurement of solubles.When present in concentrations thatare judged to impart a significant error
13、 to the soluble-fractiondata,the level of interference must be determined and correc-tions made.1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materi-als.Current edition approved Aug.1,2017.Publish
14、ed August 2017.Originallyapproved in 1994.Last previous edition approved in 2010 as D5492-10.DOI:10.1520/D5492-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the sta
15、ndards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1
16、9428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.2 It is possible that small-particle fillers and pigments andinsoluble gels present in the polymer can pass through the filterand cause errors in the measureme