1、Designation:D606207(Reapproved 2012)Standard Guide forPersonal Samplers of Health-Related Aerosol Fractions1This standard is issued under the fixed designation D6062;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last re
2、vision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide defines conventions for personal samplers ofspecific particle-size-dependent fractions of any given non-fibrous airborn
3、e aerosol.Such samplers are used for assessinghealth effects and in the setting of and testing for compliancewith permissible exposure limits in the workplace and ambientenvironment.The conventions have been adopted by theInternational Standards Organization(Technical Report ISOTR 7708),the Comit Eu
4、ropen de Normalisation(CENStandard EN 481),and the American Conference of Govern-mental Industrial Hygienists(ACGIH)(1).2The conventionswere developed(2)in part from health-effects studies reviewed(3)by the ACGIH and in part as a compromise betweendefinitions proposed by the ACGIH(3)and by the Briti
5、shMedical Research Council(BMRC)(4).Conventions are givenhere for inhalable,thoracic,and respirable fractions.1.2 This guide is complementary to Test Method D4532,which describes the performance of a particular instrument,the10-mm cyclone,and operational procedures for use.Theprocedures,specifically
6、 the optimal flow rate,are still validalthough the estimated accuracy differs somewhat from usewith previous aerosol fraction definitions.Details on thisinstrument and also the Higgins-Dewell cyclone have recentlybeen published(5-7).1.3 Limitations:1.3.1 The definitions given here were adopted by th
7、e agen-cies listed in 1.1 in part on the basis of expected health effectsof the different size fractions,but in part allowing for availablesampling equipment.The original adoption by CEN was,infact,for the eventual setting of common standards by the ECcountries while permitting the use of a variety
8、of instrumenta-tion.Deviations of the sampling conventions from health-related effects are as follows:1.3.1.1 The inhalable fraction actually depends on the spe-cific air speed and direction,on the breathing rate,and onwhether breathing is by nose or mouth.The values given in theinhalable convention
9、 are for representative values of breathingrate and represent averages over all wind directions.1.3.1.2 The respirable and thoracic fractions vary fromindividual to individual and with the breathing pattern.Theconventions are approximations to the average case.1.3.1.3 Each convention applies strictl
10、y to a fraction pen-etrating to a region,rather than depositing.Therefore,samplescollected according to the conventions may only approximatecorrelations with biological effects.For example,the respirableconvention overestimates the fraction of very small particlesdeposited in the alveolar region of
11、the respiratory systembecause some of the particles are actually exhaled withoutbeing deposited(8).In many workplaces,these very smallparticles contribute insignificantly to the sampled mass.Furthermore,the large variability between individuals and thedetails of clearance may be as important as this
12、 type of effect.1.3.1.4 The thoracic convention applies to mouth breathing,for which aerosol collection is greater than during nosebreathing.1.4 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard does not purport
13、to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3D1356 Termi
14、nology Relating to Sampling and Analysis ofAtmospheresD4532 Test Method for Respirable Dust in Workplace At-mospheres Using Cyclone Samplers1This guide is under the jurisdiction of ASTM Committee D22 on AirQualityand is the direct responsibility of Subcommittee D22.04 on Workplace AirQuality.Current
15、 edition approved April 1,2012.Published July 2012.Originallyapproved in 1996.Last previous edition approved in 2007 as D6062-07.DOI:10.1520/D6062-07R12.2The boldface numbers in parentheses refer to a list of references at the end ofthis standard.3For referenced ASTM standards,visit the ASTM website
16、,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.2 International Standards:ISO TR 7708 Technical Report on Air QualityParticleSize Fraction Definitions for Health-Related Sampling,Brussels,19934CEN EN 481 Standard on Workplace Atmospheres.SizeFraction Defi