1、Designation:D608806(Reapproved 2011)Standard Practice forInstallation of Geocomposite Pavement Drains1This standard is issued under the fixed designation D6088;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers recommendations and identifiespertinent areas of consideration for the installation of buriedgeocomposite drains us
3、ed for highway edgedrains,under-drains,or other pavement drainage applications meeting therequirements of Specification D7001.These recommendationsare intended as guidelines for developing a satisfactory con-struction and installation method to minimize installation-caused deformation or damage and
4、to provide long-termperformance of these products.It is also intended as a guidelinefor ensuring a stable underground environment for thesematerials under a wide range of service conditions.Because ofthe numerous and diverse product designs available and theinherent variability of natural ground con
5、ditions,achievingsatisfactory performance of any one product may requirereview by the engineer and modification to provisions con-tained herein to meet specific project requirements.1.2 The scope of this practice necessarily excludes productperformance criteria such as compressibility in any plane,f
6、lowcapacity,inlet capacity,or geotextile selection and use.It is,therefore,incumbent upon the product manufacturer,specifier,and project engineer to verify that the product specified for anintended application,when installed according to proceduresoutlined in this practice,will provide satisfactory
7、long termperformance according to criteria established by the owner forthat application.A commentary of product performance andinstallation factors important in achieving a satisfactory instal-lation is included in Appendix X1.1.3 The values stated in SI units are to be regarded as thestandard.The i
8、nch-pound units given in parentheses are forinformation only.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bil
9、ity of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D8 Terminology Relating to Materials for Roads and Pave-mentsD420 Guide to Site Characterization for Engineering Designand Construction Purposes(Withdrawn 2011)3D653 Terminology Relating to Soil,Rock,and ContainedFl
10、uidsD698 Test Methods for Laboratory Compaction Character-istics of Soil Using Standard Effort(12 400 ft-lbf/ft3(600kN-m/m3)D2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2487 Practice for Classification of Soils for EngineeringPurpo
11、ses(Unified Soil Classification System)D3839 Guide for Underground Installation of“Fiberglass”(Glass-Fiber Reinforced Thermosetting-Resin)PipeD4318 Test Methods for Liquid Limit,Plastic Limit,andPlasticity Index of SoilsD4439 Terminology for GeosyntheticsD7001 Specification for Geocomposites for Pav
12、ement EdgeDrains and Other High-Flow ApplicationsF412 Terminology Relating to Plastic Piping Systems3.Terminology3.1 Definitions:3.1.1 Definitions used in this practice are in accordance withTerminologies F412,D8,and D653 unless otherwise indicated.3.2 Definitions:3.2.1 aggregatea granular material
13、of mineral composi-tion such as sand,gravel,shell,slag or crushed stone(seeTerminology D8).3.2.2 dense-graded aggregatean aggregate that has aparticle size distribution such that,when it is compacted,theresulting voids between the aggregate particles,expressed as apercentage of the total space occup
14、ied by the material,arerelatively small.1This practice is under the jurisdiction of ASTM Committee D35 on Geosyn-thetics and is the direct responsibility of Subcommittee D35.03 on Permeability andFiltrationCurrent edition approved Oct.1,2011.Published November.Originally ap-proved in 1997.Last previ
15、ous edition approved in 2006 as D608806.DOI:10.1520/D6088-06R11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3T
16、he last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.3 engineerthe individual in responsible charge of thework or his duly recognized or authorized representative.3.2.4 geocomposite,na product fabricated from any com-bination of geosynthetics with geotechnical materials or othersynthetics which is used in a geotechnical application.3.2.5 geosynthetic,na p