1、Designation:D5665/D5665M99a(Reapproved 2014)1Standard Specification forThermoplastic Fabrics Used in Cold-Applied Roofing andWaterproofing1This standard is issued under the fixed designation D5665/D5665M;the number immediately following the designation indicates theyear of original adoption or,in th
2、e case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEUnits information was editorially corrected in May 2014.1.Scope1.1 This specification covers therm
3、oplastic fabrics such aspolyester,polyester/polyamide bicomponent,or compositeswith fiberglass or polyester scrims that can be used during theconstruction of cold-applied roofing and waterproofing.1.2 This specification is intended as a material specification.Issues regarding the suitability of spec
4、ific roof constructions orapplication techniques are beyond the scope of this specifica-tion.1.3 The specified tests and property values used to charac-terize the respective fabrics are intended to establish minimumproperties.In-place system design criteria or performanceattributes are factors beyon
5、d the scope of this material speci-fication.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two sy
6、stems may result in non-conformancewith the standard.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1079 Terminology Relating to Roofing and WaterproofingD1117 Guide for Evaluating Nonwoven Fabrics(Withdrawn2009)3D1776 Practice for Conditioning and Testing TextilesD1
7、777 Test Method for Thickness of Textile MaterialsD4830 Test Methods for Characterizing Thermoplastic Fab-rics Used in Roofing and WaterproofingD5035 Test Method for Breaking Force and Elongation ofTextile Fabrics(Strip Method)D5733 Test Method for Tearing Strength of NonwovenFabrics by the Trapezoi
8、d Procedure(Withdrawn 2008)33.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to Terminologies D123 and D1079.4.Classification4.1 The thermoplastic fabrics covered by this specificationare of the following general constructions and compositions.Each is a separate c
9、lass or type differentiated by the polymertype,combination of polymers,manufacturing process,orsome combination thereof.4.1.1 Type IPolyester spunbonded without resin,un-needled;4.1.2 Type IIPolyester spunbonded without resin,needled;4.1.3 Type IIIPolyester mat plus fiber glass scrim withresin;4.1.4
10、 Type IVPolyester core/polyamide sheath bicompo-nent spunbonded;4.1.5 Type VPolyester mat with polyester stitching;and4.1.6 Type VIPolyester mat plus polyester scrim withresin.4.1.7 Type VIIPolyester scrim fabric with resin.5.Materials and Manufacture5.1 The fabric shall be a uniform,thin,porous mat
11、 of theprimary thermoplastic polymer,with or without the addition ofreinforcing stranded glass or thermoplastic yarns.Chemicallybonding with a water-resistant resin or thermally bonding withother thermoplastic polymers shall be permitted.6.Physical Properties,Thickness,and Mass6.1 Fabrics shall conf
12、orm to the thickness,mass,andphysical properties presented in Table 1.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved May 1,
13、2014.Published May 2014.Originallyapproved in 1995.Last previous edition approved in 2006 as D5665 99a(2006).DOI:10.1520/D5665_D5665M-99AR14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume i
14、nformation,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.Unit Mass7.1 Determine the un
15、it mass of the fabric using the proce-dures described in Test Methods D1117.8.Workmanship,Finish,and Appearance8.1 The finished material shall be free of visible defectssuch as ragged or untrue edges,folds,creases,wrinkles,tearsand holes.9.Sampling9.1 Sample the material and determine the properties
16、 enu-merated in this specification in accordance with the testprocedures referenced herein(also see Practice D1776).10.Thickness10.1 Determine the thickness of the fabric using the proce-dures described in Test Methods D1777.11.Breaking Load and Elongation11.1 Determine the breaking load and elongation by the cutstrip method as described in Test Methods D4830 and D5035.The preferred SI unit for breaking load is kN/m.12.Trapezoid Tearing Strength12.1 Determine the trapezoid tearing strength using