1、Designation:D576218aStandard Test Method forNitrogen in Liquid Hydrocarbons,Petroleum and PetroleumProducts by Boat-Inlet Chemiluminescence1This standard is issued under the fixed designation D5762;the number immediately following the designation indicates the year oforiginal adoption or,in the case
2、 of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of nitrogen inliquid hydrocarbons,including petroleum p
3、rocess streams andlubricating oils in the concentration range from 40 g g to10 000 gg nitrogen.For light hydrocarbons containing lessthan 100 gg nitrogen,Test Method D4629 can be moreappropriate.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are include
4、d in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations
5、 prior to use.Specific warning statements are given in Section 6,7.1,8.2,and 8.2.2.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guide
6、s and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4629 Test Met
7、hod for Trace Nitrogen in Liquid Hydrocar-bons by Syringe/Inlet Oxidative Combustion and Chemi-luminescence DetectionD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System Performance3.Summary of Test Method3.1 A hydrocarbon
8、sample is placed on a sample boat atroom temperature.The sample and boat are advanced into ahigh-temperature combustion tube where the nitrogen is oxi-dized to nitric oxide(NO)in an oxygen atmosphere.The NOcontacts ozone and is converted to excited nitrogen dioxide(NO2).The light emitted as the exci
9、ted NO2decays is detectedby a photomultiplier tube,and the resulting signal is a measureof the nitrogen contained in the sample.4.Significance and Use4.1 Many nitrogen compounds can contaminate refinerycatalysts.They tend to be the most difficult class of compoundsto hydrogenate,so the nitrogen cont
10、ent remaining in theproduct of a hydrotreator is a measure of the effectiveness ofthe hydrotreating process.In lubricating oils the concentrationof nitrogen is a measure of the presence of nitrogen containingadditives.This test method is intended for use in plant controland in research.5.Apparatus5.
11、1 Boat Inlet System,capable of being sealed to the inlet ofthe combustion tube and swept with inert gas.The boats arefabricated from platinum or quartz.To aid quantitative liquidinjection,it is recommended to add a small piece of quartzwool or suitable equivalent(see 6.8)to the boat.The boat driveme
12、chanism should be able to fully insert the boat into thefurnace tube inlet section.A drive mechanism that advancesand withdraws the sample boat into and out of the furnace at acontrolled and repeatable rate is required.5.2 Chemiluminescence Detector,capable of measuringlight emitted from the reactio
13、n between nitric oxide and ozone,and containing a variable attenuation amplifier,integrator,andreadout.NOTE1Detectors designed to maintain the chemiluminescence reac-tion cell at reduced pressure are acceptable for use and were included inthe instruments used to determine the precision of this test
14、method.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved Oct.1,2018.Published October 2018.Originallyapproved in 1995.Last previous e
15、dition approved in 20178as D5762 18.DOI:10.1520/D5762-18A.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summa
16、ry of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.3 Combustion Tube