ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:94.22KB ,
资源ID:175767      下载积分:14 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/175767.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_5423_-_22.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_5423_-_22.pdf

1、Designation:D542322Standard Specification forForced-Convection Laboratory Ovens for Evaluation ofElectrical Insulation1This standard is issued under the fixed designation D5423;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year

2、 of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers forced-convection ventilatedelectrically-heated ovens,operating over all or part of thetemper

3、ature range from 20 C above the ambient temperatureto 500 C,and used for thermal endurance evaluation ofelectrical insulating materials.1.2 The specification requirements for Type I ovens arebased on IEC Publication 60216-4-1,and are technicallyidentical to it.The requirements for Type II ovens are

4、essen-tially identical to the requirements of Specification D2436.This specification and an associated test method,D5374,havereplaced Specification D2436.1.3 While the ovens covered by this specification areintended primarily for thermal endurance evaluation,theircharacteristics make them suitable f

5、or other applications asapplicable.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of

6、this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Dec

7、ision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2436 Specification for Forced-Convection Laboratory Ov-ens for Electrical Insulatio

8、n(Withdrawn 1994)3D5374 Test Methods for Forced-Convection Laboratory Ov-ens for Evaluation of Electrical Insulation2.2 Other Document:IEC Publication 60216-4-1 Electrical Insulating MaterialsThermalEndurancePropertiesPart4-1:AgeingOvensSingle-Chamber Ovens43.Terminology3.1 Definitions of Terms Spec

9、ific to This Standard:3.1.1 rate of ventilation,nthe number of air changes perhour in the oven chamber.3.1.2 set temperature,nthe average of all of the measuredtemperatures within the oven,averaged over the period of anycyclic temperature variation that occurs.3.1.2.1 DiscussionThis is the actual op

10、erating temperatureof the oven.In IEC 60216-4-1,this term is called the exposuretemperature.3.1.3 temperature fluctuation,nmaximum change in tem-perature at one point in the oven over a period of time.3.1.3.1 DiscussionThis property depends upon the sensi-tivity and type(on/off or proportional)of co

11、ntrol used and theheater mass in relation to surface area.3.1.4 temperature gradient,nthe maximum temperaturedifference at one time between any two points in the ovenchamber.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is th

12、e direct responsibility ofSubcommittee D09.17 on Fire and Thermal Properties.Current edition approved May 1,2022.Published May 2022.Originallyapproved in 1993.Last previous edition approved in 2014 as D5423 14.DOI:10.1520/D5423-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,or

13、contact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institu

14、te(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Deci

15、sion on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.4.1 DiscussionThis property depends on such factorsas uniformity of heater temperature,heater distribution aboutthe oven,a

16、nd air flow patterns within the oven.In IEC60216-4-1,this term is called the temperature difference.3.1.5 temperature variation,nmaximum change in tem-perature with time and location due to the combination oftemperature gradient and temperature fluctuation.3.1.6 thermal lag time,nthe time required for a definedspecimen to reach a specified temperature(or range of tem-perature).3.1.6.1 DiscussionThis property is largely dependentupon the rate of air circulation within the oven.In IEC60216-4-1,thi

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2