ImageVerifierCode 换一换
格式:PDF , 页数:9 ,大小:178.77KB ,
资源ID:175907      下载积分:11 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/175907.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_D_5835_-_20.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_D_5835_-_20.pdf

1、Designation:D583520Standard Practice forSampling Stationary Source Emissions for the AutomatedDetermination of Gas Concentrations1This standard is issued under the fixed designation D5835;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisi

2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice2covers procedures and equipment thatwill permit representative sampling for the automated dete

3、rmi-nation of gas concentrations of effluent gas streams withlimitations as described below.The application is limited to thedetermination of oxygen(O2),carbon dioxide(CO2),carbonmonoxide(CO),sulfur dioxide(SO2),nitric oxide(NO),nitrogen dioxide(NO2),and total oxides of nitrogen(NOx).1.2 Velocity me

4、asurements are required to determine themass flow rates of gases.This is not included in this practice.1.3 There are some combustion processes and conditionsthat may limit the applicability of this practice.Where suchconditions exist,caution and competent technical judgment arerequired,especially wh

5、en dealing with any of the following:1.3.1 Corrosive or highly reactive components,1.3.2 High vacuum,high pressure,or high temperature gasstreams,1.3.3 Wet flue gases,1.3.4 Fluctuations in velocity,temperature,or concentrationdue to uncontrollable variation in the process,1.3.5 Gas stratification du

6、e to the non-mixing of gasstreams,1.3.6 Measurements made using environmental controldevices,and1.3.7 Low levels of gas concentrations.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to addr

7、ess all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For more specific safety precautions,refer to

8、5.1.4.8,5.2.1.6,and 6.2.2.1.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organi

9、zation TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D1356 Terminology Relating to Sampling and Analysis ofAtmospheresD1608 Test Method for Oxides of Nitrogen in GaseousCombustion Products(Phenol-Disulfonic Acid Proce-dures)D3154 Test Method for Average Velocity

10、in a Duct(PitotTube Method)2.2 Other Document:40 CFR Part 60 Standards of Performance for StationarySources,Appendix A,Test Methods 2,3,3a,6,6c,7,7e,and 1043.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this practice,refer toTerminology D1356.4.Summary of Practice4.1 This practi

11、ce describes representative duct or stack gassampling,including both extractive and non-extractive sam-pling.In extractive sampling,gases are conditioned to removeaerosols,particulate matter,and other interfering substancesbefore being conveyed to instruments.In non-extractive1This practice is under

12、 the jurisdiction ofASTM Committee D22 on Air Qualityand is the direct responsibility of Subcommittee D22.03 on Ambient Atmospheresand Source Emissions.Current edition approved Dec.1,2020.Published January 2021.Originallyapproved in 1995.Last previous edition approved in 2012 as D5835 95(2012).DOI:1

13、0.1520/D5835-20.2This practice is based on ISO 10396,“Stationary source emissionsSamplingfor the automated determination of gas concentrations,”available from InternationalOrganization for Standardization,Casa Postale 56,CH-1211,Geneva,Switzerland.3For referenced ASTM standards,visit the ASTM websit

14、e,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from U.S.Government Printing Office,Superintendent ofDocuments,732 N.Capitol St.,NW,Washington,DC 20401-000

15、1,http:/www.access.gpo.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for t

16、heDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1sampling,the measurements are made in-situ;therefore,sample conditioning is not necessary beyond filtration.4.1.1 Extractive SamplingExtractive sampling consists ofextraction of the sample,removal of interfering materials,andretention of the analyte concentration without change through-out the sampling system for analysis by appropriate instrumen-t

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2