1、Designation:D5031/D5031M13(Reapproved 2018)Standard Practice forEnclosed Carbon-Arc Exposure Tests of Paint and RelatedCoatings1This standard is issued under the fixed designation D5031/D5031M;the number immediately following the designation indicates theyear of original adoption or,in the case of r
2、evision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers the selection of test conditions foraccelerated exposure testing of coatings and r
3、elated products inenclosed carbon arc devices operated according to PracticesG151 and G153.This practice also covers the preparation oftest specimens,the test conditions suited for coatings,and theevaluation of test results.Table 1 describes commonly used testconditions.1.2 This practice does not co
4、ver filtered open-flame carbon-arc exposures of paints and related coatings,which is describedin Practice D822/D822M.Another procedure for exposingthese products is covered by Practice D3361/D3361M,inwhich the specimens are subjected to radiation from anunfiltered open-flame carbon arc that produces
5、 shorter wave-lengths and higher levels of short wavelength radiation thanfiltered open flame or enclosed carbon arcs.NOTE1Practice D3361/D3361M requires use of open-flame carbon-arc apparatus with automatic humidity control.1.3 The values stated in either SI units or inch-pound unitsare to be regar
6、ded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety con
7、cerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with inte
8、rnationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D358 Spe
9、cification for Wood to Be Used as Panels inWeathering Tests of Coatings(Withdrawn 2014)3D523 Test Method for Specular GlossD609 Practice for Preparation of Cold-Rolled Steel Panelsfor Testing Paint,Varnish,Conversion Coatings,andRelated Coating ProductsD610 Practice for Evaluating Degree of Rusting
10、on PaintedSteel SurfacesD659 Method for Evaluating Degree of Chalking of ExteriorPaints(Withdrawn 1990)3D660 Test Method for Evaluating Degree of Checking ofExterior PaintsD662 Test Method for Evaluating Degree of Erosion ofExterior PaintsD714 Test Method for Evaluating Degree of Blistering ofPaints
11、D772 Test Method for Evaluating Degree of Flaking(Scal-ing)of Exterior PaintsD822/D822M Practice for Filtered Open-Flame Carbon-ArcExposures of Paint and Related CoatingsD823 Practices for Producing Films of Uniform Thicknessof Paint,Coatings and Related Products on Test PanelsD1005 Test Method for
12、Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD1186 Test Methods for Nondestructive Measurement ofDry Film Thickness of Nonmagnetic Coatings Applied toa Ferrous Base(Withdrawn 2006)3D1400 Test Method for Nondestructive Measurement of DryFilm Thickness of Nonconductive Coati
13、ngs Applied to aNonferrous Metal Base(Withdrawn 2006)3D1729 Practice for Visual Appraisal of Colors and ColorDifferences of Diffusely-Illuminated Opaque MaterialsD1730 PracticesforPreparationof AluminumandAluminum-Alloy Surfaces for Painting1This practice is under the jurisdiction of ASTM Committee
14、D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.27 on Accelerated Testing.Current edition approved Sept.1,2018.Published September 2018.Originallyapproved in 1989.Last previous edition approved in 2013 as D5031/D5031M 13.DOI:10.1520/D50
15、31_D5031M-13R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical stan
16、dard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 D2244 Practice for Calculation of Color To