1、Designation:D528821Standard Test Method forDetermining Tracking Index of Electrical Insulating MaterialsUsing Various Electrode Materials(Excluding Platinum)1This standard is issued under the fixed designation D5288;the number immediately following the designation indicates the year oforiginal adopt
2、ion or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method was developed using copper electrodesto evaluate the low-volta
3、ge(up to 600 V)tracking resistance ofmaterials in the presence of aqueous contaminants.2NOTE1At this time,only industrial laminates have been examinedusing this method,which was developed at the National ManufacturersElectrical Association(NEMA)laboratory located at the University ofCincinnati.It wa
4、s found that a closer end point(less scatter)was obtainedthan with platinum electrodes,and materials tested tended to be ranked byresin system.1.1.1 It is acceptable to consider other electrode materialsfor use with this test method depending upon the application ofthe insulating material.1.2 This t
5、est method is similar to Test Method D3638,which determines the comparative tracking index of materialsusing platinum electrodes to produce the tracking on thespecimen surface.1.3 The values stated in metric(SI)units are the standard.The inch-pound equivalents of the metric units are approxi-mate.1.
6、4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 Fi
7、re testing is inherently hazardous.Adequate safe-guards for personnel and property shall be employed inconducting these tests.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theD
8、evelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D618 Practice for Conditioning Plastics for TestingD1711 Terminology Relating to Electrical InsulationD3636 Prac
9、tice for Sampling and Judging Quality of SolidElectrical Insulating MaterialsD3638 Test Method for Comparative Tracking Index ofElectrical Insulating Materials2.2 IEC Publication:4IEC 60112 Standard Method for the Determination of theProof and the Comparative Tracking Indices of SolidInsulating Mate
10、rials,20033.Terminology3.1 DefinitionsFor definitions of terms used in this testmethod and associated with electrical and electronic insulatingmaterials,use Terminology D1711.3.2 Definitions of Terms Specific to This Standard:3.2.1 tracking index,TI,nan index for electrical insulat-ing materials whi
11、ch is arbitrarily defined as the numerical valueof that voltage which will cause failure by tracking when thenumber of drops of contaminant required to cause failure isequal to 50.3.2.1.1 DiscussionThis value is obtained from a plot ofthe number of drops required to cause failure by trackingversus t
12、he applied voltage.3.2.2 tracking index-copper electrodes,TI-Cu,na track-ing index test using copper electrodes.3.2.2.1 DiscussionThis test is comparable to comparativetracking index,Test Method D3638,with the following excep-tions:(1)copper electrodes are used instead of platinum,and1This test meth
13、od is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.12 on Electrical Tests.Current edition approved Sept.1,2021.Published October 2021.Originallyapproved in 1992.Last previous edition approved in 2014
14、 as D5288 14.DOI:10.1520/D5288-21.2Mathes,K.N.,“Surface Failure Measurements,”in Engineering DielectricsVolume IIB Electrical Properties of Solid Insulating Materials:MeasurementTechniques,STP926,ASTM International,1987.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact AST
15、M Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from International Electrotechnical Commission(IEC),3,rue deVaremb,1st floor,P.O.Box 131,CH-1211,Geneva 20,Switzerland,https:/www.iec.c
16、h.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1(2)the ele