1、Designation:D471312(Reapproved 2020)Standard Test Methods forNonvolatile Content of Heatset and Liquid Printing InkSystems1This standard is issued under the fixed designation D4713;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the determination of weightcontent of nonvolatile matter in two types of printing inks.1.2
3、 Test MethodAis applicable to heatset-type printing inksand resin solutions;solvents in such systems typically haveinitial boiling points in the range from 240 to 275C(470 to535F)and vapor pressures less than 0.2 mm Hg.1.3 Test Method B is applicable to liquid-type printing inksand vehicles based on
4、 aqueous or organic solvents that evapo-rate readily at ordinary room temperatures.NOTE1Test Method A(for heatset systems)specifies a specimen filmthickness that is much thinner than those produced by related testmethods;one exception is Test Method B in Test Methods D1259,whichis recommended as a r
5、eferee test.NOTE2Test Method B(for liquid ink systems)is similar to TestMethod D2369 except that a solvent is not required for spreading the testspecimen.1.4 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard does
6、 not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international sta
7、ndard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Refe
8、renced Documents2.1 ASTM Standards:2D1259 Test Methods for Nonvolatile Content of ResinSolutionsD2369 Test Method for Volatile Content of CoatingsE1 Specification for ASTM Liquid-in-Glass ThermometersE145 Specification for Gravity-Convection and Forced-Ventilation OvensE691 Practice for Conducting a
9、n Interlaboratory Study toDetermine the Precision of a Test Method3.Summary of Test Methods3.1 Test Method AHeatset SystemsA 0.15-g specimen ismechanically spread in a 57-mm weighing dish to a nominalthickness of 80 6 10 g/m2and heated in a forced ventilationoven at 110C for 3 h.3.2 Test Method BLiq
10、uid Ink SystemsA 0.5-g specimenis dispensed into a 57-mm weighing dish by means of adisposable syringe,mechanically spread out,and heated in anoven at 110C for 1 h.4.Significance and Use4.1 Nonvolatile content of printing inks is useful for speci-fication acceptance between the producer and the user
11、.4.2 In order to obtain accurate results for heatset systemswithin the specified 3-h heating time,the specimen filmthickness must be less than 100 g/m2,and the oven must haveforced ventilation.Thickness of the specimen film is lesscritical for liquid ink systems.5.Apparatus5.1 Balance,accurate to 1
12、mg.1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings,Materials,and Applications and are the directresponsibility of Subcommittee D01.56 on Printing Inks.Current edition approved June 1,2020.Published July 2020.Originally approvedin 1987.Last previous e
13、dition approved in 2012 as D4713 12.DOI:10.1520/D4713-12R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyri
14、ght ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International St
15、andards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.5.2 Oven,forced-ventilation type conforming to Type IIB inSpecification E145 and maintained at 110 6 2C.5.3 Thermometer,capable of reading 110 6 2C and con-forming to Specification E1.
16、Alternately,temperature measur-ing devices such as liquid-in-glass thermometers,thermistors,thermocouples,or platinum resistance thermometers that pro-vide equivalent or better accuracy and precision,that cover thetemperature range specified,may be used.5.4 Weighing Dish,such as an aluminum foil dish 57 mmwide,the lid of a 1-lb ink can 94 mm wide,or otherflat-bottomed container.The bottom of the container must nothave a trough or depression into which the test material mightcollect.5.5 Spatula,o