1、Designation:D4585/D4585M18Standard Practice forTesting Water Resistance of Coatings Using ControlledCondensation1This standard is issued under the fixed designation D4585/D4585M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the yea
2、r of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers basic principles and operatingprocedures for testing water resistance of coatings usingcontrolle
3、d condensation.Condensation is produced by expos-ing one surface of a coated specimen to a heated,saturatedmixture of air and water vapor,while the reverse side of thespecimen is exposed to the cooling effect of room temperatureair.This practice is derived from research of the ClevelandSociety for C
4、oatings Technology.21.2 This practice is limited to the methods of obtaining,measuring,and controlling conditions and procedures of con-trolled condensation tests.It does not specify specimenpreparation,specific test conditions,or evaluation of results.NOTE1Alternative practices for testing water re
5、sistance of coatingsinclude Practices D870,D1735,and D2247.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues
6、from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and dete
7、r-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendati
8、ons issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D609 Practice for Preparation of Cold-Rolled Steel Panelsfor Testing Paint,Varnish,Conversion Coatings,andRelated Coating ProductsD610 Practice for Evaluating Degree of Rusti
9、ng on PaintedSteel SurfacesD714 Test Method for Evaluating Degree of Blistering ofPaintsD823 Practices for Producing Films of Uniform Thicknessof Paint,Coatings and Related Products on Test PanelsD870 Practice for Testing Water Resistance of CoatingsUsing Water ImmersionD1654 Test Method for Evaluat
10、ion of Painted or CoatedSpecimens Subjected to Corrosive EnvironmentsD1730 PracticesforPreparationof AluminumandAluminum-Alloy Surfaces for PaintingD1735 Practice for Testing Water Resistance of CoatingsUsing Water Fog ApparatusD2247 Practice for Testing Water Resistance of Coatings in100%Relative H
11、umidityD2616 Test Method for Evaluation of Visual Color Differ-ence With a Gray ScaleD3359 Test Methods for Rating Adhesion by Tape TestD3363 Test Method for Film Hardness by Pencil TestD4541 Test Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersG154 Practice for Operating Fluo
12、rescent Ultraviolet(UV)Lamp Apparatus for Exposure of Nonmetallic Materials3.Summary of Practice3.1 Water vapor is generated by heating a pan of water at thebottom of the test chamber.The specimens form the roof orwalls of the test chamber so that the back sides of thespecimens are exposed to the co
13、oling effects of room tempera-ture air.The resulting heat transfer causes vapor to condense onthe test specimens as liquid water saturated with air.1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility
14、ofSubcommittee D01.27 on Accelerated Testing.Current edition approved July 1,2018.Published July 2018.Originally approvedin 1986.Last previous edition approved in 2013 as D4585 13.DOI:10.1520/D4585_D4585M-18.2Foecking,N.J.,“Cleveland Condensing Type Humidity Cabinet,”OffcialDigest,December 1963,Vol
15、35,No.467,pp.13181327;and Higgins,W.A.,“Cleveland Condensing Type Humidity Cabinet:II,”Offcial Digest,November1965,Vol 37,No.490,pp.13921404.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume i
16、nformation,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World