1、Designation:D469012(Reapproved 2018)Standard Specification forUrea-Formaldehyde Resin Adhesives1This standard is issued under the fixed designation D4690;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num
2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 Thisspecificationcoversthreetypesofurea-formaldehyde ther
3、mosetting resin adhesives suitable for use onwood,wood-based substrates,or plastic laminates.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are provided forinformation only.1.3 The requirements for the adhesive are based on tests ofphysical proper
4、ties including viscosity,density,nonvolatilecontent,pH,insoluble matter,amylaceous matter,mixingproperties,working life,and on strength properties,includingdry shear strength in lumber-type joints,dry and wet shearstrength in plywood-type joints,and all strength tests at the endof the storage life c
5、ertified by the manufacturer.1.4 The following safety hazards caveat pertains only to thetest method portion,Sections 8 through 11,of this specifica-tion:This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this sta
6、ndard to establish appropriate safety,health,and environmental practices and determine the appli-cability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on
7、Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2B417 Test Method for Apparent Density of Non-Free-Flowing Metal Powders Using the Carney Funn
8、elD905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD906 Test Method for Strength Properties of Adhesives inPlywood Type Construction in Shear by Tension LoadingD907 Terminology of AdhesivesD1084 Test Methods for Viscosity of AdhesivesD1489 Test Method for Nonv
9、olatile Content of AqueousAdhesivesD1490 Test Method for Nonvolatile Content of Urea-Formaldehyde Resin SolutionsD1583 Test Method for Hydrogen Ion Concentration of DryAdhesive FilmsD1875 Test Method for Density of Adhesives in Fluid FormD2556 Test Method for Apparent Viscosity of AdhesivesHaving Sh
10、ear-Rate-Dependent Flow Properties Using Ro-tational ViscometryD5266 Practice for Estimating the Percentage of WoodFailure in Adhesive Bonded JointsE70 Test Method for pH of Aqueous Solutions With theGlass ElectrodeE104 Practice for Maintaining Constant Relative Humidityby Means of Aqueous Solutions
11、2.2 Federal Specifications:3PPP-C-96 Cans,Metal,28 Gage and LighterPPP-D-723 Drums,FiberPPP-D-729 Drums,Shipping and Storage,Steel,55-gal(208-L)2.3 Federal Standard:3FED-STD-123 Marking for Shipment2.4 Military Standard:3MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 DefinitionsMany te
12、rms in this specification are de-fined in Terminology D907.3.2 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved Aug.1,2018.P
13、ublished August 2018.Originallyapproved in 1987.Last previous edition approved in 2012 as D4690 12.DOI:10.1520/D4690-12R18.This specification is intended as a replacement for Federal SpecificationMMM-A-188c,Adhesive;Urea Resin Type(Liquid and Powder).2For referenced ASTM standards,visit the ASTM web
14、site,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-509
15、8,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for
16、theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.1 lotadhesive manufactured at one place from thesame batch or blends of raw materials subjected to the sameoperations and conditions.NOTE1In this specification,the maple block lamination in TestMethod D905 and the birch plywood construction in Test Method D906are described as assemblies.4.Significance and Use4.1 This specification provides te